How does my clutch and Flywheel look?

Wi Stang · May 6, 2007

Well I took everything out of the car since I am replacing my bellhousing, and I think the clutch and flywheel look OK to me, but I don't have too much experience on how this stuff should look.
So here is the flywheel. There are some shallow groves in it down the center.

Here is a closeup of a portion of the flywheel

Here is the flywheel side of the clutch disk

Let me know how it looks. It has been used on the car for about 7 months last summer with a couple of trips to the dragstrip.
Thanks

urban96 · May 6, 2007

i would buy a new insert for that FW

go-stang5.0 · May 6, 2007

Uhhhh...you got some pretty mean heat checking there. What kinda disc is that and how does the PP look?

Wi Stang · May 7, 2007

The pressure plate looked really good. There were no groves in it, or heat marks.
The clutch is a Spec Stage 3+.

divit250r · May 7, 2007

This looks like a crack to me, and I agree that the insert looks pretty rough with all the hot spots. Also, the shot of the clutch disc shows that the material has smeared. It looks like it got really hot a few times.

Scott

kck6894 · May 7, 2007

that's pretty much what my stage 3+ always looks when I take it apart. My pressure plate useually looked the same as the flywheel though.

Wi Stang · May 7, 2007

Originally Posted by divit250r
This looks like a crack to me

It really does look like a crack in the picture. After I got home I checked it out, and it is just a spot where some clutch dust has collected where the Pressure plate is bolted on. I took the flywheel to get looked at, and it is not warped. I think I am just going to get a new center section for the flywheel, and a new clutch disk.

Originally Posted by kck6894
that's pretty much what my stage 3+ always looks when I take it apart. My pressure plate useually looked the same as the flywheel though.

Good to know kck6894. Did you just put it back in then, or did you do something to it? And if you put it back in, how did it hold up after that point?

Thanks.

kck6894 · May 8, 2007

Wi Stang said:
It really does look like a crack in the picture. After I got home I checked it out, and it is just a spot where some clutch dust has collected where the Pressure plate is bolted on. I took the flywheel to get looked at, and it is not warped. I think I am just going to get a new center section for the flywheel, and a new clutch disk.

Good to know kck6894. Did you just put it back in then, or did you do something to it? And if you put it back in, how did it hold up after that point?

Thanks.

I put a new one in every year. I've used the spec clutches for 2 years and finally switched it this year. Any time I used one for more than a year about 2 months into the second race season they would start slipping. If your pressure plate looks nice and it's heat checked it will probably be fine. Put a new friction plate on the flywheel and use it. I've pulled mine apart after some limited use and it looked similar to yours. I put the new friction plate on the flywheel and used it for a while and didn't have any problems with it.

MysteryMachine · May 8, 2007

if i was that far into it I'd prolly just replace it. Stupid to ave to tear it down again if you have to do it if somethign bad happens to it. But I don't know **** about that kinda stuff so I don't know whats good and what ain't

How does my clutch and Flywheel look?

Wi Stang

Member

urban96

bubb rubb says:"woo woooooo"

go-stang5.0

New Member

Wi Stang

Member

divit250r

Member

Attachments

kck6894

Advanced Member

Wi Stang

Member

kck6894

Advanced Member

MysteryMachine

Active Member

Similar threads

How does my clutch and Flywheel look?

Member

bubb rubb says:"woo woooooo"

New Member

Member

Member

Attachments

Advanced Member

Member

Advanced Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency