Hyd T5 stuff

woodsnake · Sep 2, 2007

Good Sunday morning to all you guys. I know I don't post over here very often, life sucks a lot , as I'm sure you all know. Any way, I have a 69 Cougar that I am going to put a T5 into. I have the trans, bell housing, clutch pedal, etc.. But I'm curious about the hydraulic clutch parts. Mustangs unlimited sells a kit for like four hundred bones, and I'd really like to be able to spend a bit less than that. Does anyone know the part numbers from that kit, or has any one else done the same thing for less money? It looks pretty simple for the cash!

Help!!

As I don't post here very often, if you want to share the info you can email me direct at

woodsnake4462838@msn.com

Thanks again!

CraigMBA · Sep 2, 2007

Call McCloud and see how much they get for it.

My customer has a t56 in his 70 Cougar and bought all the parts from Dark Horse. They were all McCloud.

5.0ina66 · Sep 2, 2007

You can clone the JME hyd setup sold by most vendors pretty closely using CNC brand parts, and if you want, you can even relocate the flange like JME does and have your own homemade JME setup. Cost is $225-250-ish

JamesW · Sep 2, 2007

http://midnightdsigns.com/Mustang/HYD Clutch.htm

rbohm · Sep 2, 2007

the dazecars parts are quality parts. well finished and definately well worth the money. now if i just had the time and energy to get going on my mustang

woodsnake · Sep 6, 2007

How do you source the 'CNC brand parts'? I found the daze cars page, that was some good reading. I do have some fabrication skills, but I don't have a welder, or air compressor, and am therefore somewhat limited. Thanks for the links!

10secgoal · Sep 6, 2007

You can't source the master cylinder from CNC. It is made specifically for JMC. You can buy the straight version and try to get that to work. You can source the slave cylinder from CNC though.

jikelly · Sep 6, 2007

Man there's a link to my page on there. I've got to update that website, and how.

jikelly · Sep 6, 2007

Um you don't need to spend two arms and a leg to do a hyd clutch setup on your stang BTW.

5.0ina66 · Sep 6, 2007

10secgoal said:
You can't source the master cylinder from CNC. It is made specifically for JMC. You can buy the straight version and try to get that to work. You can source the slave cylinder from CNC though.

I *think* JMC modifies the CNC master themselves as it looks like the flange has been stick welded. JamesW's page shows how to make a JMC-esque setup using stock versions of the CNC parts used by JMC.

As to the OP, it's cncbrakes.com.

10secgoal · Sep 6, 2007

5.0ina66 said:
I *think* JMC modifies the CNC master themselves as it looks like the flange has been stick welded. JamesW's page shows how to make a JMC-esque setup using stock versions of the CNC parts used by JMC.

As to the OP, it's cncbrakes.com.

Nah, it's all tig welded. And they really aren't exactly the same as the straight versions. Everyone of them is hand made by the owner of CNC himself. Cuts, bores, hones, (don't know about welded though) everyone of them himself. I was given a little lesson on this when the man himself stopped by the shop today.

rbohm · Sep 6, 2007

the master and dlave cylinders are avilable from speedway motors. thats where daze sources his from in the instructions he sends with the brackets. they are reasonably priced too, about $110 for both.

5.0ina66 · Sep 7, 2007

10secgoal said:
Nah, it's all tig welded. And they really aren't exactly the same as the straight versions. Everyone of them is hand made by the owner of CNC himself. Cuts, bores, hones, (don't know about welded though) everyone of them himself. I was given a little lesson on this when the man himself stopped by the shop today.

Cool! I stand corrected..wish I could TIG!

Hyd T5 stuff

woodsnake

CraigMBA

New Member

5.0ina66

Member

JamesW

Member

rbohm

woodsnake

10secgoal

Active Member

jikelly

jikelly

5.0ina66

Member

10secgoal

Active Member

rbohm

5.0ina66

Member

Similar threads

Hyd T5 stuff

New Member

Member

Member

Active Member

Member

Active Member

Member

Similar threads

Privacy & Transparency

Privacy & Transparency