• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

I'm Looking For Info

  • Thread starter Thread starter Foxbody_ViNo
  • Start date Start date Mar 7, 2017

Im doing a 2.3 conversion to a 5.0

  • Do I need a carb regulator

    Votes: 0 0.0%
  • And a sub tank

    Votes: 0 0.0%

  • Total voters
    0
  • 1
  • 2
Next
1 of 2 Next Last

Foxbody_ViNo

Member
Mar 7, 2017
9
2
13
Mar 7, 2017
#1
  • Mar 7, 2017
  • #1
I'm looking for info on what else I need to convert my foxbody to a carb
 
D

Dart68

Member
Jun 6, 2016
87
22
18
Mar 7, 2017
#2
  • Mar 7, 2017
  • #2
Foxbody_ViNo said:
I'm looking for info on what else I need to convert my foxbody to a carb
Click to expand...
Not sure what you mean by "sub tank" but you will need a fuel pressure regulator if that's what you mean by "carb regulator".
 

Foxbody_ViNo

Member
Mar 7, 2017
9
2
13
Mar 7, 2017
#3
  • Mar 7, 2017
  • #3
Dart68 said:
Not sure what you mean by "sub tank" but you will need a fuel pressure regulator if that's what you mean by "carb regulator".
Click to expand...




Yes I meant to put carberuator and I got a old engine it's a 1984 flat tappet and I took out the 2.3 that was in the car and left all the wiring so I can have heater and a.c. but do u think it will work with the carberuator?? And I still have old fuel pump so do I leave that alone or wat??
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,134
10,752
213
polk county florida
Mar 7, 2017
#4
  • Mar 7, 2017
  • #4
What year and skill level?
 

Foxbody_ViNo

Member
Mar 7, 2017
9
2
13
Mar 7, 2017
#5
  • Mar 7, 2017
  • #5
karthief said:
What year and skill level?
Click to expand...



93 coupe and 7 skill level
 

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Mar 7, 2017
#6
  • Mar 7, 2017
  • #6
You need a fuel pressure regulator for a carbed engine with a return line. With that the stock pump will be fine.

When I used Aeromotive I had to use another non return regulator to cut pressure to 6psi. The aeromotive only cut pressure to 15psi. I think there was a restrictor somewhere in the return line.

The distributor has to be a vacuum advance style. Other than that I really can't think of anything else.

...a turbo
...nitrous
...lol
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 7, 2017
#7
  • Mar 7, 2017
  • #7
Are you the kind of guy that draws mustaches and beards on pictures of beautiful women? If so convert an EFI car to carb.



If not, save your money for an EFI engine, 87 or later. Then you get to rebuild the whole car to make it anywhere equal to an original 5.0 Fox.
See http://forums.stangnet.com/showthread.php?t=516785 for details on the 4 cylinder to 8 cylinder conversion. The only interchangeable parts are the body and the dash and rear body wiring harnesses. You need a 5.0 fox roller to strip for parts, because the 87-93 fox 5.0 is a very different car from the 4 cylinder car.

EFI to carb swaps

Revised 16-Dec-2015 to add necessity of mounting external electrical fuel pump below the level of the bottom of the fuel tank

A word of warning on EFI to carb swaps: don’t expect to pass emissions in any state that does comprehensive smog inspections, because it won’t happen. Some states will not title or issue license plates to cars that have been converted from EFI to carb. Be aware that you are violating several Federal laws concerning the removal of pollution control equipment. If you operate the vehicle on public highways and get caught by state or federal law enforcement (doubtful, but possible) you could be subject to fines and imprisonment. You won't get any more power from a carb than you will from a properly maintained and tuned EFI system.

The following information is intended for informational purposes only. Operation of a motor vehicle modified in such as manner as described below should be limited to off road use only.

Doing the swap; you must know how to read electrical diagrams and wire circuits to properly do the swap. Don’t take shortcuts or cut corners in the fabrication of the electrical or mechanical assemblies. If you do NASCAR quality work, the car will look good, run good and be as reliable as a carb’d car can be. Take pride in a job done with excellence.

If you are one of those few people who do excellent work, please disregard my negative comments. They are not intended for you.

Quality, quality, quality…
Some of the motivation of my negative comments about EFI to carb has to do with the quality of electrical workmanship. A lot of the wiring “repairs” that I have seen on the road and in the junkyard looks like road kill. The other part of my negative view stems from people who can’t grasp the operation and tuning of EFI. Carbs have their own set of requirements and some learning is required to get the best performance. Every car is different and each installation needs to be tuned to get the best performance. Putting an “out of the box carb” or one from someone else’s car isn’t the way to success. There is no auto compensation for small variations in carbs like there is for EFI. Just throwing a carb on a car because you won’t bother to learn how EFI works is a poor excuse.


Now that the rant is over, here’s some practical advice…

1. Do not use an EFI in tank fuel pump with a carb. You will never get the pressure/flow regulated properly. If the add on pressure regulator fails, you will flood the engine with gas and wash all the oil off the cylinder walls. That will cost you big time $$$. Either go full EFI or use a tank/fuel pump/fuel lines out of an 84 or earlier Stang. Fabricating your own setup is possible but there are some snags to overcome.

2. Do not attempt to leave the EFI computer in place in an attempt to control either the electric fuel pump or ignition. Doing so qualifies you for the “Road Kill Mechanics Award”.

3. If you try to use your current tank, you will need to pull the fuel pump out and fabricate a pickup tube & strainer sock to replace the fuel pump. Or you can have a sump fabricated and welded onto you existing tank. Many welding shops will not weld fuel tanks because of the dangers involved if the tank isn't purged properly.

4. You will need an external electric fuel pump unless you change the timing cover for one with the mechanical fuel pump mount on it. The external pump will have to be mounted below the bottom of the tank to get the siphon effect needed to keep the pump fed sufficiently. Rip all the EFI wiring out, and the computer controlled fuel pump won't work. You will need to add a relay & switch and wire in the existing inertia switch for an external low pressure electric fuel pump. Do not try to wire the fuel pump without the relay. The 15-20 amps the pump pulls will overload the circuit. This will take power away from other items on the same circuit or cause the fuse or fuse link to blow.

5.

6. You will need to run some new fuel feed lines or braided hose. The 3/8" aluminum tubing works well, but you will need a flaring tool and bending springs to fabricate the lines. Braided hose is easy to run and route, but is much more expensive. It is about $3.50-$4.00 a foot plus the end fittings, which are $3-$4 each. Fabricating hose assembles can be difficult, but anyplace that makes hydraulic hoses can do it for you for an extra charge. See http://www.amazonhose.com for more information.

7. For some help fabricating your own stainless steel hose assemblies, see
8. http://www.turbinefun.com/Stainless_Braided_Hose_Assembly.asp

9. For stainless steel braided hose and fittings for automotive use:

10. See http://www.summitracing.com/search/?keyword=stainless steel hose&dds=1
11. http://www.summitracing.com/search/?keyword=stainless steel hose&dds=1

12. http://www.jegs.com/webapp/wcs/stor...hall&searchTerm=stainless+steel+hose&x=18&y=4

13. See http://www.eaton.com/Eaton/Product...rformanceProducts/FittingsProducts/index.htm for more information on High performance automotive hose products

14. AN fittings require a 37 degree flaring tool. A standard automotive or household plumbing tool is 45 degrees and cannot be used with AN flare fittings. If you do, the flare is subjected to too much stress when the fitting is tightened, and is likely to fail or leak.

15. See http://www.mscdirect.com/ , http://www.mcmaster.com/ or for the flaring tool you will need . Prices start at $85 and go up

16. http://www1.mscdirect.com/CGI/N2DRVSH?PACACHE=000000013509163
17.

18. http://www.mcmaster.com/#flaring-tools/=b4fxc3
19.


20. Last time I was in Summit racing, they had a 37 degree flaring tool for less than $40. It may or may not be a catalog item.

21. While you are at the electrical part, you'll need a Duraspark or similar ignition system. The 85 Mustang GT 5 speed has a suitable Duraspark distributor with a steel gear compatible with the roller camshaft. The EFI ignition depends on the EFI sensors to advance the spark. Rip out the TPS and MAP/Baro sensors and the computer will have no idea of the proper ignition timing for best performance. Running a fixed timing setting is only for test purposes or for a race track only car. Don't try it on the street: the results will not be nearly as good as a properly setup Duraspark or equal. Crane makes a really nice distributor for non-EFI applications. . See http://www.cranecams.com/index.php?show=browseParts&lvl=4&prt=127 for more information. Cost is about $400, which makes the 85 Mustang reman units look really appealing.


Duraspark II ignition diagram:

Diagram courtesy of /www.billwrigley.com

See http://webpages.charter.net/1bad6t/duraspark.html for more help.
Note the ballast resistor shown in the diagram: you’ll need that too
If you use a coil from a 78 or later Mustang, you don't need the ballast resistor. The stock 89 Ford/Mustang ignition coil does not need a ballast resistor


A simpler HEI ignition that uses the same distributor and fewer parts can be found here. This is an excellent resource, and I suggest that you add it to your Internet Favorites
http://www.binderplanet.com/forums/showthread.php?t=48435

22. Tools needed:
23. Crimp tool for connector pins $9-$30 AutoZone, NAPA, Advance Auto Parts or other store
24. 100-150 watt soldering gun (recommend WELLER 8200PK soldering gun kit 100/140W) $30 at Lowes or $40 at Home Depot
25. 3/32”-1/8” rosin core electrical solder, 1/4 lb roll $6 at Ace Hardware, Home Depot or Lowes
26. Assorted sizes of heat shrink tubing. Buy long pieces and cut length to fit. It is cheaper that way. http://www.partsexpress.com/webpage.cfm?&WebPage_ID=346&CFID=169547&CFTOKEN=34300345
27. Hot air gun to shrink the tubing ($30-$40) Home Depot
28. Jeweler’s screwdriver kit $5 at Ace Hardware
29. Assorted automotive wire, 18-16 gauge 10’-20’ foot spools in different colors. $5 a roll at Advance Auto Parts.
30. Ford connector pins AutoZone, NAPA or other store $5-$10 for a kit of 10-12 assorted pins

31. You will have $110-$150 in materials and tools if you don't already have them.

32. The water temp and oil pressure signals feed from the sender to the main harness through the 10 pin EFI engine harness. To utilize these senders, you need to identify the wires and find a way to reconnect them to the main harness after the EFI engine harness is removed. You need a weatherproof quick connector to join the sender wiring to the main harness.

33. See the graphic for the 10 pin connector circuit layout.

34. The injector power pin is the VPWR pin in the black 10 pin connector.


35. You will need to construct a wiring harness from the ‘85 carb distributor to the Duraspark box if you go Duraspark, or other distributor to coil wiring.
36. The voltmeter picks up its signal from the switched voltage present on the instrument panel, so you don’t need to worry about that.

37. The fuel tank gauge is also independent of the computer wiring.

38. AutoZone wiring diagrams can be found if you are willing to dig through the self help repair section of their website. http://www.autozone.com/autozone/re...3835D6CFF5E3A5037BBBD332CF445FF.diyprod2-b2c3

39. How to solder View: http://youtu.be/uaYdCRjDr4A


40. Soldering pigtails onto existing pins is road kill quality work as far as I am concerned. Take some time to study the way the Ford connectors are assembled and you will find that a small jeweler’s screwdriver will release the pins from the connector shell. New pins and a crimping tool are available from the Standard Motor Parts or Bendix Electrical parts line that the NAPA & Bumper to Bumper Auto Parts stores carry. Ask any auto parts store about Standard Motor Products or Bendix Electrical wiring parts. Those that carry them will be able to get the parts you need. AutoZone has a cheap kit with 10 pins for about $5. Just enough pins to leave you short when assembling a connector.

41. One of the interesting things about the Ford OEM wiring diagrams is that the connector shape on the drawing matches the connector shape in the car. That makes it easier to identify connectors and circuits. OEM Ford diagrams are available at for an 85 Mustang at http://www.helminc.com/helm/Result....edia=&mscsid=2M838NG3R5SR2MCS00A3HVE05T03C501 or can be found in the Chilton series of auto repair manuals for Mustangs.

42. The following is an excellent idea from a fellow Stangnetter who tackled the wiring plan the right way. He obtained the wiring diagrams from an 85 carb'd V8 Mustang and laid them out side by side with the diagrams from his car. He then traced out each circuit and the wire colors and connectors associated with them. After tracing the circuit and connectors for a circuit, he laid out the changes he needed to make. One circuit at a time made a difficult big job into many smaller easy to manage jobs.

43. Copied from pikapp33.
JR’s comments:
I have heard that there have been quality problems with some of these Richporter distributors, but that may be a limited quantity of the units.

I recently changed my EFI mustang back to carb with MSD ignition, to save some money and go for a more simplistic approach. I researched, and found the best stock type distributor to use was from an 83 Bronco 5.0, which is a Duraspark (magnetic pickup, same as what MSD dists use), making it possible to use the 2 wire MSD trigger input, and also has a steel gear to work with the EFI hydraulic roller cam.

I chose to use a Richporter FD30 ($85). Then added a BWD C194A Cap Adapter ($12) to use the Fox style dist cap/wires (the Richporter comes with cap/rotor, which I didn't use; other brands come without and are cheaper, but have a core as well; no core on this one). And then a BWD D166 rotor ($6) to match the cap adapter. I also chose to buy the MSD 8869 adapter wire ($20ish) to connect the dist to the MSD harness for my 6AL. All together about $125, much cheaper than the MSD billet dists, and am very happy with the quality of the the dist and the way the setup worked out.

The Richporter FD30 distributor is available at Advance Auto Parts ($90) & O’Riley’s ($81)
 
Last edited: Mar 7, 2017
Reactions: 88LXSleeper and HotFox

CarMichael Angelo

my rearend will smell so minty fresh,
15 Year Member
Nov 29, 1999
10,641
8,909
234
Birmingham, al
Mar 7, 2017
#8
  • Mar 7, 2017
  • #8
jrichker said:
Are you the kind of guy that draws mustaches and beards on pictures of beautiful women? If so convert an EFI car to carb.



If not, save your money for an EFI engine, 87 or later. Then you get to rebuild the whole car to make it anywhere equal to an original 5.0 Fox.
See http://forums.stangnet.com/showthread.php?t=516785 for details on the 4 cylinder to 8 cylinder conversion. The only interchangeable parts are the body and the dash and rear body wiring harnesses. You need a 5.0 fox roller to strip for parts, because the 87-93 fox 5.0 is a very different car from the 4 cylinder car.

EFI to carb swaps

Revised 16-Dec-2015 to add necessity of mounting external electrical fuel pump below the level of the bottom of the fuel tank

A word of warning on EFI to carb swaps: don’t expect to pass emissions in any state that does comprehensive smog inspections, because it won’t happen. Some states will not title or issue license plates to cars that have been converted from EFI to carb. Be aware that you are violating several Federal laws concerning the removal of pollution control equipment. If you operate the vehicle on public highways and get caught by state or federal law enforcement (doubtful, but possible) you could be subject to fines and imprisonment. You won't get any more power from a carb than you will from a properly maintained and tuned EFI system.

The following information is intended for informational purposes only. Operation of a motor vehicle modified in such as manner as described below should be limited to off road use only.

Doing the swap; you must know how to read electrical diagrams and wire circuits to properly do the swap. Don’t take shortcuts or cut corners in the fabrication of the electrical or mechanical assemblies. If you do NASCAR quality work, the car will look good, run good and be as reliable as a carb’d car can be. Take pride in a job done with excellence.

If you are one of those few people who do excellent work, please disregard my negative comments. They are not intended for you.

Quality, quality, quality…
Some of the motivation of my negative comments about EFI to carb has to do with the quality of electrical workmanship. A lot of the wiring “repairs” that I have seen on the road and in the junkyard looks like road kill. The other part of my negative view stems from people who can’t grasp the operation and tuning of EFI. Carbs have their own set of requirements and some learning is required to get the best performance. Every car is different and each installation needs to be tuned to get the best performance. Putting an “out of the box carb” or one from someone else’s car isn’t the way to success. There is no auto compensation for small variations in carbs like there is for EFI. Just throwing a carb on a car because you won’t bother to learn how EFI works is a poor excuse.


Now that the rant is over, here’s some practical advice…

1. Do not use an EFI in tank fuel pump with a carb. You will never get the pressure/flow regulated properly. If the add on pressure regulator fails, you will flood the engine with gas and wash all the oil off the cylinder walls. That will cost you big time $$$. Either go full EFI or use a tank/fuel pump/fuel lines out of an 84 or earlier Stang. Fabricating your own setup is possible but there are some snags to overcome.

2. Do not attempt to leave the EFI computer in place in an attempt to control either the electric fuel pump or ignition. Doing so qualifies you for the “Road Kill Mechanics Award”.

3. If you try to use your current tank, you will need to pull the fuel pump out and fabricate a pickup tube & strainer sock to replace the fuel pump. Or you can have a sump fabricated and welded onto you existing tank. Many welding shops will not weld fuel tanks because of the dangers involved if the tank isn't purged properly.

4. You will need an external electric fuel pump unless you change the timing cover for one with the mechanical fuel pump mount on it. The external pump will have to be mounted below the bottom of the tank to get the siphon effect needed to keep the pump fed sufficiently. Rip all the EFI wiring out, and the computer controlled fuel pump won't work. You will need to add a relay & switch and wire in the existing inertia switch for an external low pressure electric fuel pump. Do not try to wire the fuel pump without the relay. The 15-20 amps the pump pulls will overload the circuit. This will take power away from other items on the same circuit or cause the fuse or fuse link to blow.

5.

6. You will need to run some new fuel feed lines or braided hose. The 3/8" aluminum tubing works well, but you will need a flaring tool and bending springs to fabricate the lines. Braided hose is easy to run and route, but is much more expensive. It is about $3.50-$4.00 a foot plus the end fittings, which are $3-$4 each. Fabricating hose assembles can be difficult, but anyplace that makes hydraulic hoses can do it for you for an extra charge. See http://www.amazonhose.com for more information.

7. For some help fabricating your own stainless steel hose assemblies, see
8. http://www.turbinefun.com/Stainless_Braided_Hose_Assembly.asp

9. For stainless steel braided hose and fittings for automotive use:

10. See http://www.summitracing.com/search/?keyword=stainless steel hose&dds=1
11. http://www.summitracing.com/search/?keyword=stainless steel hose&dds=1

12. http://www.jegs.com/webapp/wcs/stores/servlet/KeywordSearchCmd?storeId=10001&catalogId=10002&langId=-1&N=0&Ntt=stainless+steel+hose&Ntk=all&Nty=1&D=stainless+steel+hose&Ntx=mode+matchall&Dx=mode+matchall&searchTerm=stainless+steel+hose&x=18&y=4

13. See http://www.eaton.com/Eaton/ProductsServices/ProductsbyName/Aeroquip/AeroquipPerformanceProducts/FittingsProducts/index.htm for more information on High performance automotive hose products

14. AN fittings require a 37 degree flaring tool. A standard automotive or household plumbing tool is 45 degrees and cannot be used with AN flare fittings. If you do, the flare is subjected to too much stress when the fitting is tightened, and is likely to fail or leak.

15. See http://www.mscdirect.com/ , http://www.mcmaster.com/ or for the flaring tool you will need . Prices start at $85 and go up

16. http://www1.mscdirect.com/CGI/N2DRVSH?PACACHE=000000013509163
17.

18. http://www.mcmaster.com/#flaring-tools/=b4fxc3
19.


20. Last time I was in Summit racing, they had a 37 degree flaring tool for less than $40. It may or may not be a catalog item.

21. While you are at the electrical part, you'll need a Duraspark or similar ignition system. The 85 Mustang GT 5 speed has a suitable Duraspark distributor with a steel gear compatible with the roller camshaft. The EFI ignition depends on the EFI sensors to advance the spark. Rip out the TPS and MAP/Baro sensors and the computer will have no idea of the proper ignition timing for best performance. Running a fixed timing setting is only for test purposes or for a race track only car. Don't try it on the street: the results will not be nearly as good as a properly setup Duraspark or equal. Crane makes a really nice distributor for non-EFI applications. . See http://www.cranecams.com/index.php?show=browseParts&lvl=4&prt=127 for more information. Cost is about $400, which makes the 85 Mustang reman units look really appealing.


Duraspark II ignition diagram:

Diagram courtesy of /www.billwrigley.com

See http://webpages.charter.net/1bad6t/duraspark.html for more help.
Note the ballast resistor shown in the diagram: you’ll need that too
If you use a coil from a 78 or later Mustang, you don't need the ballast resistor. The stock 89 Ford/Mustang ignition coil does not need a ballast resistor


A simpler HEI ignition that uses the same distributor and fewer parts can be found here. This is an excellent resource, and I suggest that you add it to your Internet Favorites
http://www.binderplanet.com/forums/showthread.php?t=48435

22. Tools needed:
23. Crimp tool for connector pins $9-$30 AutoZone, NAPA, Advance Auto Parts or other store
24. 100-150 watt soldering gun (recommend WELLER 8200PK soldering gun kit 100/140W) $30 at Lowes or $40 at Home Depot
25. 3/32”-1/8” rosin core electrical solder, 1/4 lb roll $6 at Ace Hardware, Home Depot or Lowes
26. Assorted sizes of heat shrink tubing. Buy long pieces and cut length to fit. It is cheaper that way. http://www.partsexpress.com/webpage.cfm?&WebPage_ID=346&CFID=169547&CFTOKEN=34300345
27. Hot air gun to shrink the tubing ($30-$40) Home Depot
28. Jeweler’s screwdriver kit $5 at Ace Hardware
29. Assorted automotive wire, 18-16 gauge 10’-20’ foot spools in different colors. $5 a roll at Advance Auto Parts.
30. Ford connector pins AutoZone, NAPA or other store $5-$10 for a kit of 10-12 assorted pins

31. You will have $110-$150 in materials and tools if you don't already have them.

32. The water temp and oil pressure signals feed from the sender to the main harness through the 10 pin EFI engine harness. To utilize these senders, you need to identify the wires and find a way to reconnect them to the main harness after the EFI engine harness is removed. You need a weatherproof quick connector to join the sender wiring to the main harness.

33. See the graphic for the 10 pin connector circuit layout.

34. The injector power pin is the VPWR pin in the black 10 pin connector.


35. You will need to construct a wiring harness from the ‘85 carb distributor to the Duraspark box if you go Duraspark, or other distributor to coil wiring.
36. The voltmeter picks up its signal from the switched voltage present on the instrument panel, so you don’t need to worry about that.

37. The fuel tank gauge is also independent of the computer wiring.

38. AutoZone wiring diagrams can be found if you are willing to dig through the self help repair section of their website. http://www.autozone.com/autozone/re...3835D6CFF5E3A5037BBBD332CF445FF.diyprod2-b2c3

39. How to solder View: http://youtu.be/uaYdCRjDr4A


40. Soldering pigtails onto existing pins is road kill quality work as far as I am concerned. Take some time to study the way the Ford connectors are assembled and you will find that a small jeweler’s screwdriver will release the pins from the connector shell. New pins and a crimping tool are available from the Standard Motor Parts or Bendix Electrical parts line that the NAPA & Bumper to Bumper Auto Parts stores carry. Ask any auto parts store about Standard Motor Products or Bendix Electrical wiring parts. Those that carry them will be able to get the parts you need. AutoZone has a cheap kit with 10 pins for about $5. Just enough pins to leave you short when assembling a connector.

41. One of the interesting things about the Ford OEM wiring diagrams is that the connector shape on the drawing matches the connector shape in the car. That makes it easier to identify connectors and circuits. OEM Ford diagrams are available at for an 85 Mustang at http://www.helminc.com/helm/Result.asp?Style=&Mfg=FMC&Make=FCT&Model=MUST&Year=1985&Category=&Keyword=&Module=&selected_media=&mscsid=2M838NG3R5SR2MCS00A3HVE05T03C501 or can be found in the Chilton series of auto repair manuals for Mustangs.

42. The following is an excellent idea from a fellow Stangnetter who tackled the wiring plan the right way. He obtained the wiring diagrams from an 85 carb'd V8 Mustang and laid them out side by side with the diagrams from his car. He then traced out each circuit and the wire colors and connectors associated with them. After tracing the circuit and connectors for a circuit, he laid out the changes he needed to make. One circuit at a time made a difficult big job into many smaller easy to manage jobs.

43. Copied from pikapp33.
JR’s comments:
I have heard that there have been quality problems with some of these Richporter distributors, but that may be a limited quantity of the units.

I recently changed my EFI mustang back to carb with MSD ignition, to save some money and go for a more simplistic approach. I researched, and found the best stock type distributor to use was from an 83 Bronco 5.0, which is a Duraspark (magnetic pickup, same as what MSD dists use), making it possible to use the 2 wire MSD trigger input, and also has a steel gear to work with the EFI hydraulic roller cam.

I chose to use a Richporter FD30 ($85). Then added a BWD C194A Cap Adapter ($12) to use the Fox style dist cap/wires (the Richporter comes with cap/rotor, which I didn't use; other brands come without and are cheaper, but have a core as well; no core on this one). And then a BWD D166 rotor ($6) to match the cap adapter. I also chose to buy the MSD 8869 adapter wire ($20ish) to connect the dist to the MSD harness for my 6AL. All together about $125, much cheaper than the MSD billet dists, and am very happy with the quality of the the dist and the way the setup worked out.

The Richporter FD30 distributor is available at Advance Auto Parts ($90) & O’Riley’s ($81)
Click to expand...


You do realize that somebody that can't even spell carburetor won't even bother to read that don't you?
 
Reactions: General karthief and jrichker

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 7, 2017
#9
  • Mar 7, 2017
  • #9
madmike1157 said:
You do realize that somebody that can't even spell carburetor won't even bother to read that don't you?
Click to expand...
Miracles still do happen....
 
Reactions: General karthief

CarMichael Angelo

my rearend will smell so minty fresh,
15 Year Member
Nov 29, 1999
10,641
8,909
234
Birmingham, al
Mar 7, 2017
#10
  • Mar 7, 2017
  • #10
jrichker said:
Miracles still do happen....
Click to expand...
Yeah but,...the second coming of Christ?

Cause that's the kind of miracle you'd have to expect for somebody to press..............* check spelling *
 
D

Dart68

Member
Jun 6, 2016
87
22
18
Mar 7, 2017
#11
  • Mar 7, 2017
  • #11
Foxbody_ViNo said:
Yes I meant to put carberuator and I got a old engine it's a 1984 flat tappet and I took out the 2.3 that was in the car and left all the wiring so I can have heater and a.c. but do u think it will work with the carberuator?? And I still have old fuel pump so do I leave that alone or wat??
Click to expand...
Ok, if you want to run a carb the most pressure you want, measured at the carb, is 6-7 psi. If the electric fuel pump that's in the car works then you can just get regulator to drop the pressure down. Depending on the regulator and/or how much pressure your pump puts out you might not need a return line. However, dead heading an electric pump against the regulator will shorten the life span of the pump unless the pump has an internal bleed valve to bleed off fuel pressure when not needed.

One thing to note...if you plan to run this car on the street you'd better check the emission regulations first before you do this and then find out later that you can't even get plates for it because it won't pass an emission inspection.
 

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Mar 7, 2017
#12
  • Mar 7, 2017
  • #12
I read it and can't spell carb....see my fingers froze up. They won't allow me....aaarrgghh

Jrichker is correct about the fuel pump. I converted mine from necessity but the correct way would be to pull the pump and wire in an external pump with a relay.

Every time I see a carburrethttor converted car the price figures go down...even if its a race car. I've been down that road and its a lot easier to go carbureted but the end result is, usually, a car that looks cheap. Everyone knows a carb conversioned motor is the easy way out. Especially, if you use a stock efi dizzy.

Did you catch the three words I threw in just for you madmike1157 ?
 
Reactions: General karthief

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,134
10,752
213
polk county florida
Mar 7, 2017
#13
  • Mar 7, 2017
  • #13
poking the bear
To act in such a way that has a good, but not definite chance, of causing trouble. (You can poke a bear once and maybe get away with it, but if you keep poking him, he's going to get really angry.) To stir things up.
 
Reactions: 90sickfox

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Mar 7, 2017
#14
  • Mar 7, 2017
  • #14
@ madmike1157
 
Reactions: General karthief

CarMichael Angelo

my rearend will smell so minty fresh,
15 Year Member
Nov 29, 1999
10,641
8,909
234
Birmingham, al
Mar 8, 2017
#15
  • Mar 8, 2017
  • #15
90sickfox said:
I read it and can't spell carb....see my fingers froze up. They won't allow me....aaarrgghh

Jrichker is correct about the fuel pump. I converted mine from necessity but the correct way would be to pull the pump and wire in an external pump with a relay.

Every time I see a carburrethttor converted car the price figures go down...even if its a race car. I've been down that road and its a lot easier to go carbureted but the end result is, usually, a car that looks cheap. Everyone knows a carb conversioned motor is the easy way out. Especially, if you use a stock efi dizzy.

Did you catch the three words I threw in just for you madmike1157 ?
Click to expand...

karthief said:
poking the bear
To act in such a way that has a good, but not definite chance, of causing trouble. (You can poke a bear once and maybe get away with it, but if you keep poking him, he's going to get really angry.) To stir things up.
Click to expand...

90sickfox said:
@ madmike1157
Click to expand...

Hey,..your not bothering me in the leats as longas you guys dont mind looking like you cant read or right who ami to correct you?


And for the record, you only used one "fingernail on a chalkboard" word.
Also for the record,...I do not hibernate in the forum waiting till somebody comes along to poke me awake. If I throw out a derog comment about the fact that somebody managed to make it all the way through high school, and can't be bothered to either correct the words with the little red wigglies beneath them, or go back and fix them after they get pointed out, makes them both dumb and lazy. So, in other words,.....I'm poking the bear myself. I typically expect to get poked back.

But as things go in the world of face book and twitter,..a comment made yesterday is ancient history, and nobody composing a thread in a web forum should be expected to look like they have a brain......I mean,....On the other carburetor conversion thread, it's STILL about a efi to carb convertion.

"Hey Thag here.....me wanna put 4 hole thing on motor that make gas go into engine...you help please.
 
Last edited: Mar 8, 2017
Reactions: General karthief and 90sickfox

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,134
10,752
213
polk county florida
Mar 8, 2017
#16
  • Mar 8, 2017
  • #16
Mike makes hanging around here so entertaining, if he's not correcting someone's spelling or getting the 'facts' straight, he's providing us with the wity adventures of dealing with the monster.
And he's willing to poke himself.
Long live the Bear.
 
Reactions: 90sickfox

Foxbody_ViNo

Member
Mar 7, 2017
9
2
13
Mar 8, 2017
#17
  • Mar 8, 2017
  • #17
Thanks for the advice @90sickfox and to all then other vatos that wanna troll keep on its funny asf #Mexicanpride I know how to spell #f@$* trump hahahahahahah
 

Foxbody_ViNo

Member
Mar 7, 2017
9
2
13
Mar 8, 2017
#18
  • Mar 8, 2017
  • #18
Thanks for the advice @90sickfox and to all them other vatos that wanna troll keep on its funny asf #Mexicanpride I know how to spell #f@$* trump hahahahahahah
 
Reactions: 90sickfox

90sickfox

Wasn't a pretty sight...and I've got big hands
SN Certified Technician
Mar 2, 2015
6,953
5,831
213
Mar 8, 2017
#19
  • Mar 8, 2017
  • #19
Hey Loco...welcome to the dark side of the forum. You're not anybody in here till your thread gets highjacked

The great thing about these cars is we can do what we want with them. I've been there man.

What's your next plan ( after carb ) for your car ? Do you have any pics ?
 

Foxbody_ViNo

Member
Mar 7, 2017
9
2
13
Mar 8, 2017
#20
  • Mar 8, 2017
  • #20
90sickfox said:
Hey Loco...welcome to the dark side of the forum. You're not anybody in here till your thread gets highjacked

The great thing about these cars is we can do what we want with them. I've been there man.

What's your next plan ( after carb ) for your car ? Do you have any pics ?
Click to expand...







Yea i got pics and maybe just a 150 shot of nitrous
 
Reactions: 90sickfox
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

M
Rim suggestions
  • mason5.0
  • Sep 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
13
Views
402
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 9, 2026
Qtrhrse23
Ignition Question
  • WantAn88GT
  • Sep 12, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
280
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 13, 2026
WantAn88GT
T
Need help with 302 swap
  • thxmxrgx
  • Sep 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
283
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 24, 2026
thxmxrgx
T
Fox Brake lines hitting bump stops
  • keel
  • Sep 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
18
Views
552
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 24, 2026
keel
Brake pad and rotor upgrade
  • Sparky714
  • Aug 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
634
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 17, 2026
Sparky714
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?