in the middle of a intake swap

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 11, 2006

#1

• Feb 11, 2006

• #1

What did you use to take the hose the screw under the egr valve?if im putting the 93 cobra intake on will i need to reuse it?

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 11, 2006

#2

• Feb 11, 2006

• #2

NM

 

SeventyMach1

Keep it lubed .... keep it straight .... and keep

Mar 30, 2005

1,940

3

36

North Carolina

Feb 11, 2006

#3

• Feb 11, 2006

• #3

OK

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 11, 2006

#4

• Feb 11, 2006

• #4

need help with disconnecting fuel lines,how do i disconnect it.do i put the tool on the rubber to pull the hose off.any help will be greatful

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 11, 2006

#5

• Feb 11, 2006

• #5

here is a pic i took

http://pg.photos.yahoo.com/ph/mustangcobra0495/album?.dir=/aafd

 

mytight95

Active Member

Apr 11, 2003

2,605

0

46

Dothan,Al

Feb 11, 2006

#6

• Feb 11, 2006

• #6

slide the tool in the opening on the rail side of that fitting, then pull out on the rubber side of the line......



jason

 

VibrantRedGT

"STANGNET'S PENGUIN SMACKER"

15 Year Member

Nov 29, 1999

14,679

424

154

Boca Raton, Florida

Feb 11, 2006

#7

• Feb 11, 2006

• #7

You don't have to disconnect the fuel lines from the rail. Just move it out of the way. Lay the new intake down then put the rails on. Quicker, easier and less mess.

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 11, 2006

#8

• Feb 11, 2006

• #8

VibrantRedGT said:

You don't have to disconnect the fuel lines from the rail. Just move it out of the way. Lay the new intake down then put the rails on. Quicker, easier and less mess.

Click to expand...

After spending a hour on it,that is what i decided to do.So now i have the everything off except the lower intake i forgot to drain to coolant.What is a quick way to drain it? and i heard that there is a coolant line that i should not hook up to the nipple sticking out of cobra intake.Any tips for me from where am at.The intake i have is a 93 cobra intake.

thanks
Jesse

 

RIO5.0

15 Year Member

Feb 16, 2001

6,892

8

128

N.H.

Feb 11, 2006

#9

• Feb 11, 2006

• #9

Take the thermo housing off and the undo the metal coolant lines that feed back to the heater core...it'll be a mess but that'll drain the coolant...

What's the skinny on the nipple and feeding coolant to the upper???? is this the lower or upper your talking about??

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 12, 2006

#10

• Feb 12, 2006

• #10

here is where i found the info about the coolant line

http://forums.stangnet.com/showthread.php?t=578261&highlight=fuel+line+disconnect

 

RIO5.0

15 Year Member

Feb 16, 2001

6,892

8

128

N.H.

Feb 12, 2006

#11

• Feb 12, 2006

• #11

95mustang_gt said:

here is where i found the info about the coolant line

http://forums.stangnet.com/showthread.php?t=578261&highlight=fuel+line+disconnect

Click to expand...

"since you do not use a EGR spacer with cobra intake.....make sure you do not hook up the coolant line to the nipple sticking out of cobra intake."


Soon as I read your post I knew that's what you where refering to....You got that info from the 5.0 tech forum....Its not an issue for a SN95...we have no such line...
On that 2nd pic in that post you can either plug it....or use it to REPLACE the vac line that USED to feed your oil fill vent....depending on your valve covers..

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 12, 2006

#12

• Feb 12, 2006

• #12

alright thanks,Well now im going to be putting the lower intake on.I have a question about the oring and diamond shape gasket that comes with the felpro set.What are those for?

 

S

Synned

took tubgirl on a date and got banned

Mar 31, 2005

991

1

0

Philly

Feb 12, 2006

#13

• Feb 12, 2006

• #13

95mustang_gt said:

alright thanks,Well now im going to be putting the lower intake on.I have a question about the oring and diamond shape gasket that comes with the felpro set.What are those for?

Click to expand...

EGR?

 

RIO5.0

15 Year Member

Feb 16, 2001

6,892

8

128

N.H.

Feb 12, 2006

#14

• Feb 12, 2006

• #14

The O-Ring is for the dizzy...lube it with Vaseline or such and install....

Blue ends seals go front/rear to seal it...



You can see one here...make sure its CLEAN where it lay's down, RTV the corners where it meets the heads to seal that area..

My bad....The diamond shaped gasket is for the IAC valve....

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 12, 2006

#15

• Feb 12, 2006

• #15

well now i got to go to the auto store to grab some pintle hats because they were pretty brittle.

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 12, 2006

#16

• Feb 12, 2006

• #16

What egr hose goes into the vacuum tree under the upper intake green or red hose?

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 12, 2006

#17

• Feb 12, 2006

• #17

here is where im stuck i have to hose one green and one red and then i have the vapor canister hose.Does the vapir canister hose plug into the vacuum tree?

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 12, 2006

#18

• Feb 12, 2006

• #18

here is a pic

http://pg.photos.yahoo.com/ph/mustangcobra0495/album?.dir=/f892

 

9

95mustang_gt

New Member

Mar 30, 2005

364

1

0

Wisconsin

Feb 12, 2006

#19

• Feb 12, 2006

• #19

anyone??

 

RIO5.0

15 Year Member

Feb 16, 2001

6,892

8

128

N.H.

Feb 12, 2006

#20

• Feb 12, 2006

• #20

95mustang_gt said:

here is where im stuck i have to hose one green and one red and then i have the vapor canister hose.Does the vapir canister hose plug into the vacuum tree?

Click to expand...

Yes it USE to plug into the vac tree on your stock intake...You need to feed it vacuum somehow....Easy way would be a Tee off the FRP feed or use one of the small tubes on the vac tree under the upper....

Remove the EGR tube at the header and cap it...



I only used one of the small feeds here so you could grab vac there?