• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

installing rotors, need help ASAP!

  • Thread starter Thread starter DerekStangGT
  • Start date Start date Jun 30, 2005
D

DerekStangGT

My package is in the mail!
Feb 18, 2003
1,068
0
36
Jun 30, 2005
#1
  • Jun 30, 2005
  • #1
i have drilled/slotted rotors, but i got the two sides mixed up. which way do the slots point? i thought the top of the slot always points forward is this correct? also, the calipers are marked left and right. is the right side the passenger side and the left side, the drivers side? thanks for the help
 
S

SilverGTV8

New Member
Nov 30, 2003
295
0
0
West Brookfield, MA
Jun 30, 2005
#2
  • Jun 30, 2005
  • #2
Top of the slot point back.
 

96WhiteNight

New Member
May 11, 2004
303
0
0
Carlisle, PA
Jun 30, 2005
#3
  • Jun 30, 2005
  • #3
Yea the top of the slot points back and yes the right side is the passenger side.
 
D

DerekStangGT

My package is in the mail!
Feb 18, 2003
1,068
0
36
Jun 30, 2005
#4
  • Jun 30, 2005
  • #4
thanks a lot. better late than never i guess. now ihave to rip off the pass side and replace it w/ the other rotor. my instructor said it doesnt matter..... one more question. where do the banjo bolts go? are they for the brake lines?

edit: never mind, trial and error works wonders
 

Marks5.0!

Founding Member
Jan 27, 2000
640
2
0
San Antonio, TX
Jun 30, 2005
#5
  • Jun 30, 2005
  • #5
depends upon the manufactor some have the top of the slot facing the rear while others (brembo and baer) have the top of the slot facing forward
 
D

DerekStangGT

My package is in the mail!
Feb 18, 2003
1,068
0
36
Jun 30, 2005
#6
  • Jun 30, 2005
  • #6
Marks5.0! said:
depends upon the manufactor some have the top of the slot facing the rear while others (brembo and baer) have the top of the slot facing forward
Click to expand...
so with brembo rotors, the top of the slot should face the front? i have brembos and i just put them in facing the rear since thats what i was JUST told
 

Marks5.0!

Founding Member
Jan 27, 2000
640
2
0
San Antonio, TX
Jun 30, 2005
#7
  • Jun 30, 2005
  • #7
quote from a brembo FAQ.
all of Brembo's slotted discs are directional as well, regardless of the vane geometry. The discs should be installed such that the end of the slot nearest the outer edge of the disc contacts the pad first.
so when going forward the rotors will be going counter clockwise so the top of the slot would need to be facing forward in order to be first in contacting the pad

Mark
 

DropTopPony

Noob Slayer
Founding Member
Aug 13, 2002
2,570
3
48
south jersey
Jun 30, 2005
#8
  • Jun 30, 2005
  • #8
i have the same rotors you bought and they were labeled r & l with the slots facing back not front. this confused me also cause my powerslots said go forward...but i have mine facing back with no problems.
 

Nuar

Founding Member
Apr 16, 2002
570
0
16
NB, CT
Jun 30, 2005
#9
  • Jun 30, 2005
  • #9
Poor man lol
Look on the brightside! You will be able to change your rotors blindfolded after this hehe.
God i'd be pissed if i had to do the same job so many times...
 

tomustang

Psychotic Member
Founding Member
Jun 8, 2000
3,434
2
78
McLean Hospital
Jun 30, 2005
#10
  • Jun 30, 2005
  • #10
Just as long as you don't have 2 lefts or 2 rights you can cross the rotors any way you way. Oh and don't forget if you bleed the brakes afterward and the pedal is still light, bleed the master cylinder.
 
D

DerekStangGT

My package is in the mail!
Feb 18, 2003
1,068
0
36
Jun 30, 2005
#11
  • Jun 30, 2005
  • #11
tomustang said:
Just as long as you don't have 2 lefts or 2 rights you can cross the rotors any way you way. Oh and don't forget if you bleed the brakes afterward and the pedal is still light, bleed the master cylinder.
Click to expand...
how do you bleed the master? its sad that i took my brakes class two semesters ago and forgot everything btw, i installed my new rotors and calipers, and test drove it for ~5 min, let them cool for ~10 min, then drove home ~20 miles and they are now cooling. problem is that my driver side rotor has grooves in it now. and both rotors are discolored. its like there was dirt on the pads and have been spread around the whole rotor. also, my steering wheels shakes violently when i brake, usually a sign of warped rotors. is all this common dufing the break in peroid?
 

Marks5.0!

Founding Member
Jan 27, 2000
640
2
0
San Antonio, TX
Jun 30, 2005
#12
  • Jun 30, 2005
  • #12
shouldnt have any shaking at all. from my first drive with my new rotors and pads braking was smooth as glass.
If the rotors are zinc coated there will be some discoloring until it wears completely off the surface the pad runs on
 
D

DerekStangGT

My package is in the mail!
Feb 18, 2003
1,068
0
36
Jun 30, 2005
#13
  • Jun 30, 2005
  • #13
Marks5.0! said:
shouldnt have any shaking at all. from my first drive with my new rotors and pads braking was smooth as glass.
If the rotors are zinc coated there will be some discoloring until it wears completely off the surface the pad runs on
Click to expand...
here are some pics to show the direction of the slots and the discoloration



sorry for the quality, its from my camera phone
 

Attachments

  • 49192595_159773129_0.webp
    7.5 KB · Views: 151
  • 49192595_159773126_0.webp
    11.9 KB · Views: 162

Marks5.0!

Founding Member
Jan 27, 2000
640
2
0
San Antonio, TX
Jun 30, 2005
#14
  • Jun 30, 2005
  • #14
everything looks good to me
mine had the same type discoloration when they were 1st put on.
heres a pic to compare it
 

Attachments

  • 232Picture-111.webp
    79.4 KB · Views: 113
D

DerekStangGT

My package is in the mail!
Feb 18, 2003
1,068
0
36
Jun 30, 2005
#15
  • Jun 30, 2005
  • #15
Marks5.0! said:
everything looks good to me
mine had the same type discoloration when they were 1st put on.
heres a pic to compare it
Click to expand...
your slots are facing forward though, mine are facing back. will it make that much of a difference? i'll be adding SS lines next week, should i swap the rotors around while im in there?

EDIT: is all DOT 3 brake fluid created equal? i forgot to buy some, so i just used some cheapo O'reilly's fluid from the shop's tool room. should i buy some better quality stuff for my new lines?
 

Attachments

  • 232Picture-111.webp
    79.4 KB · Views: 102

Marks5.0!

Founding Member
Jan 27, 2000
640
2
0
San Antonio, TX
Jun 30, 2005
#16
  • Jun 30, 2005
  • #16
Unless Brembo changed direction in the past 6 months, the slots should actually be like mine.
depending on how the cooling vanes are designed in the rotor, the cooling may be affected a bit.
For brake fluid i would get some good dot4. That valvaline synpower stuff is pretty good for the money

Mark
 
You must log in or register to reply here.

Similar threads

Brakes Brake caliper ID help
  • kidott
  • Sep 2, 2025
  • Fox 5.0 Mustang Tech
Replies
1
Views
296
Fox 5.0 Mustang Tech Sep 2, 2025
AeroCoupe
J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
332
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
T
Fox Convertible top issues
  • TDM389
  • Feb 15, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
470
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 15, 2026
General karthief
T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
215
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
346
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?