installing rotors, need help ASAP!

DerekStangGT

My package is in the mail!
Feb 18, 2003
1,068
0
36
i have drilled/slotted rotors, but i got the two sides mixed up. which way do the slots point? i thought the top of the slot always points forward :shrug: is this correct? also, the calipers are marked left and right. is the right side the passenger side and the left side, the drivers side? thanks for the help
 
thanks a lot. better late than never i guess. now ihave to rip off the pass side and replace it w/ the other rotor. my instructor said it doesnt matter..... one more question. where do the banjo bolts go? are they for the brake lines?

edit: never mind, trial and error works wonders :nice:
 
Marks5.0! said:
depends upon the manufactor some have the top of the slot facing the rear while others (brembo and baer) have the top of the slot facing forward
so with brembo rotors, the top of the slot should face the front? i have brembos and i just put them in facing the rear since thats what i was JUST told
 
quote from a brembo FAQ.
all of Brembo's slotted discs are directional as well, regardless of the vane geometry. The discs should be installed such that the end of the slot nearest the outer edge of the disc contacts the pad first.
so when going forward the rotors will be going counter clockwise so the top of the slot would need to be facing forward in order to be first in contacting the pad

Mark
 
i have the same rotors you bought and they were labeled r & l with the slots facing back not front. this confused me also cause my powerslots said go forward...but i have mine facing back with no problems.
 
Poor man lol :)
Look on the brightside! You will be able to change your rotors blindfolded after this hehe.
God i'd be pissed if i had to do the same job so many times...
 
tomustang said:
Just as long as you don't have 2 lefts or 2 rights you can cross the rotors any way you way. Oh and don't forget if you bleed the brakes afterward and the pedal is still light, bleed the master cylinder. :nice:
how do you bleed the master? its sad that i took my brakes class two semesters ago and forgot everything :nonono: btw, i installed my new rotors and calipers, and test drove it for ~5 min, let them cool for ~10 min, then drove home ~20 miles and they are now cooling. problem is that my driver side rotor has grooves in it now. and both rotors are discolored. its like there was dirt on the pads and have been spread around the whole rotor. also, my steering wheels shakes violently when i brake, usually a sign of warped rotors. is all this common dufing the break in peroid?
 
shouldnt have any shaking at all. from my first drive with my new rotors and pads braking was smooth as glass.
If the rotors are zinc coated there will be some discoloring until it wears completely off the surface the pad runs on
 
Marks5.0! said:
shouldnt have any shaking at all. from my first drive with my new rotors and pads braking was smooth as glass.
If the rotors are zinc coated there will be some discoloring until it wears completely off the surface the pad runs on
here are some pics to show the direction of the slots and the discoloration

49192595_159773129_0.webp

49192595_159773126_0.webp

sorry for the quality, its from my camera phone :notnice:
 

Attachments

  • 49192595_159773129_0.webp
    49192595_159773129_0.webp
    7.5 KB · Views: 151
  • 49192595_159773126_0.webp
    49192595_159773126_0.webp
    11.9 KB · Views: 162
Marks5.0! said:
everything looks good to me
mine had the same type discoloration when they were 1st put on.
heres a pic to compare it
232Picture-111.webp
your slots are facing forward though, mine are facing back. will it make that much of a difference? i'll be adding SS lines next week, should i swap the rotors around while im in there?

EDIT: is all DOT 3 brake fluid created equal? i forgot to buy some, so i just used some cheapo O'reilly's fluid from the shop's tool room. should i buy some better quality stuff for my new lines?
 

Attachments

  • 232Picture-111.webp
    232Picture-111.webp
    79.4 KB · Views: 102
Unless Brembo changed direction in the past 6 months, the slots should actually be like mine.
depending on how the cooling vanes are designed in the rotor, the cooling may be affected a bit.
For brake fluid i would get some good dot4. That valvaline synpower stuff is pretty good for the money

Mark