intake manifold install

IntenseBlue

Member
Jul 10, 2005
946
0
16
Does anyone know of a website to walk me through the removal and install of an upper and lower 5.0 intake? I was going to install it last weekend, but my partner chickened out. I'm kind or weary about it, but not really. I hope to knock it out from 8AM to anywhere before 8PM. All help appreciated. Pictures, instructions, anything helps.
 
click on link below and pick one up at local auto parts store or order online. i have one on every car i own.it contains step by step instructions & pictures on everything from vehicle maint. instructions,recomended fluids,torq specs. total rebuild, and upper & lowerintake removal and install. my mustang manuals has saved me $1000's of dollars. i'll guarantee you wont regret the purchase because if you don't like it return it for a refund you can't loose.

http://www.repairmanual.com/automobiles/1988/14/2707
 
it is in line with the carbon cannister and controls the fuel vapor out of the cannister its normally closed .when the engine is shut off, vapors from the fuel tank flow into the cannister. when the engine is started , the solenoid engages and opens , purging the vapors into the engine with the solenoid open ,vapors from the fuel tank are routed directly into the engine.this is part of your vehicles emissions control system. i use the chilton repair manual its a little more expensive but contains better pictures and info.
 
Be sure to visit this site for vacuum diagrams, wiring diagrams, intake bolt torque pattern and lots of other good information: http://www.veryuseful.com/mustang/tech/engine/

Here's some tips...

Tools: a good torque wrench is a must have item. A razor blade scraper that holds a single edge razor blade from Home Depot or Ace hardware is another handy thing. Get a Chilton or Haynes shop manual - you'll need it for the bolt torques and patterns. The intake manifold has an especially odd pattern. You'll need access to a timing light to set the timing after you re-stab the distributor. Look in the A/C repair section for the fuel line tools. They look like little plastic top hats. You will need the 1/2" & 5/8" ones. The hat shaped section goes on facing the large part of the coupling. Then you press hard on the brim until it forces the sleeve into the coupling and releases the spring. You may need someone to pull on the line while you press on the coupling. Put some motor oil on them when you put the line back together.

The A/C Compressor comes off with lines still connected. Mark all the electrical, smog and vacuum lines with tags to help you remember where to re-connect them. If you have a digital camera, take several pictures.

Whatever you do, don't skimp on cleaning the gasket surfaces. New gaskets need to seat against bare metal and not the residue left from the old gaskets in order to seal leak free. This is the most time consuming and tiresome part of the job. Look for little things that need to be replaced like the short hose from the thermostat hosing to the water pump, damaged vacuum lines and hose clamps that are rusted or broken.

Plan on cutting the thermostat to water pump hose, or removing the thermostat housing. Also plan on removing the distributor to get clearance to remove the intake manifold. Remove #1 spark plug, stick your finger in the spark plug hole and crank. When your finger gets air moving past it, stop cranking. Turn the engine until the timing marks line up with the pointer. Now you can pull the distributor out.

My favorite trick that saves time and effort is the stay in place gasket. Be sure that you scrape (don't use a wire brush) all the old gasket material off, then clean all the surfaces with acetone or MEK.

When the surfaces are clean, use weather strip adhesive on the head to manifold surface, and on the side of the gasket that mates to the head. Follow the instructions on the tube or can and when it gets tacky, press the gasket down on the head.

Clean the area where the rubber rails mount to the block in front and in the rear with more acetone or MEK and do the same trick with the weather strip adhesive that you did to the heads.

Coat the rubber seals and the gasket area around the water passages with lots of Blue Silicone gasket sealer and put it together. Wala! no leaks, and no gaskets that shifted out of place.

Fuel injector seal kits with 2 O rings and a pintle cap (Borg-Warner P/N 274081) are available at Pep Boys auto parts. Cost is about $2.74 per kit. The pintle caps fit either injectors with a pin sticking out the injector end or 4 with more tiny holes in the injector end. The following are listed at the Borg-Warner site ( http://www.borg-warner.com ) as being resellers of Borg-Warner parts:

http://www.partsplus.com/ or http://www.autovalue.com/ or http://www.pepboys.com/ or http://www.federatedautoparts.com/
 
sorry i dont have a diagram or anything but that cable un-snaps from the TB and you just unbolt the throttle bracket off of the left side of the TB. Make sure you mark each vacuum line with tape or something and label them to where each vacuum goes. This is what I did after i unhooked the neg. battery cable, First I drained my coolant system. Second I released the pressure of my fuel system by the shrader valve(located behind your altenator on the fuel rail). Next I pulled vacuum lines and marked them. Then i just started unbolting my cold air intake, then the MAF,TB, EGR, and then i started working into my Upper Intake. You should get some gasket sealer too and seal up those gaskets, read the instructions for the torque specs when bolting it back on too. Let us know if u have trouble
 
Richker's instructions are excellent. One tip I'll add -- rather than using adhesive on the gaskets, run to the local hardware store with one of your lower intake bolts, and the shorter of your upper intake bolts. Buy 4 bolts to match the lower, and 2 to match the upper. Cut the hex heads off and slot that end -- turning them into studs. When mounting the lower/upper, put the temporary studs in (4 corners for lower, one in front/back for upper) and use them to locate the gaskets and to make it easy to 'stab' the manifold without misaligning gaskets. Once the manifolds are in place, start another couple of bolts, and then remove your temporary studs and put the rest of the bolts in.

Use the proper tightening pattern for the lower. Don't exceed 18-20 ft-lbs. on the lower or 10-12 ft-lbs. for the upper. The castings aren't very strong and it doesn't take much to seal them.
 
Be very careful removing the bolts in the corners of the lower. They go into the water passages and tend to break during removal. Sometimes it helps to go back and forth with then during removal. I got lucky, hopefully you will too!!
 
IntenseBlue said:
How do I remove the cable that open/shuts the throttle blade?

just get a screwdriver and place it between the plastic parts and the cable and pry, it's just a ball socket connection and will just pop off.

The worst part for me when I changed my intake was cleaning the old gaskets off. Once you have the upper and lower off and you're in the cleaning mode, make sure you don't get water/coolant anywhere it shouldn't be. Drain your radiator before you start and soak up any access before you start splashing it around. There are also four little metal tabs in the corners once you have your intakes removed, be careful not to break these, they help line up your new gaskets. It won't kill you if you do, but it's a whole lot easier if they are still there.

Just out of curiousity, are you replacing stock with stock? Did you crack your original or something?
 
Michael Yount said:
Richker's instructions are excellent. One tip I'll add -- rather than using adhesive on the gaskets, run to the local hardware store with one of your lower intake bolts, and the shorter of your upper intake bolts. Buy 4 bolts to match the lower, and 2 to match the upper. Cut the hex heads off and slot that end -- turning them into studs. When mounting the lower/upper, put the temporary studs in (4 corners for lower, one in front/back for upper) and use them to locate the gaskets and to make it easy to 'stab' the manifold without misaligning gaskets. Once the manifolds are in place, start another couple of bolts, and then remove your temporary studs and put the rest of the bolts in.

I used Michael's advice when I did mine, and it worked like a charm.

Sounds like you got all the advice you need, it really isn't that hard. Just take your time and label everything you take off.
 
Repostyle said:
just get a screwdriver and place it between the plastic parts and the cable and pry, it's just a ball socket connection and will just pop off.

The worst part for me when I changed my intake was cleaning the old gaskets off. Once you have the upper and lower off and you're in the cleaning mode, make sure you don't get water/coolant anywhere it shouldn't be. Drain your radiator before you start and soak up any access before you start splashing it around. There are also four little metal tabs in the corners once you have your intakes removed, be careful not to break these, they help line up your new gaskets. It won't kill you if you do, but it's a whole lot easier if they are still there.

Just out of curiousity, are you replacing stock with stock? Did you crack your original or something?

I'm gonna do it this Sunday. Thanks for the help guys. I think I'm set now. I've got the gaskets Tom that you reccomended. Also, I'm installing a TMOSS ported lower. Gonna get some headers and then it's on to GT40s.
 
Cleaning

Application : 1992 upper intake manifold

Got a quick question. I removed a polished upper intake manifold from
another mustang and want to install it on mine, the intake itself it spotless on the outside but if I look inside its caked with oil and dirt, I'm pretty sure that the surface on the inside is supposed to be spotless. You can only see 50% of the inside of this thing so I'm guessing that the whole thing is dirty inside. Any tips on how to clean out the inside of the upper intake manifold and restore it to the stock clean state? Thanks
 
NO easy way to do it. A significant part of the deposits are blowby and do not come out in a solvent bath although the oily deposits will. To get it perfectly clean, you have to press out the freeze plugs in the ends of the plenum and sand/bead blast the entire inside of the intake, hen press new 1 3/4" freeze plugs back in both ends. I do this on every upper I port and it's a significant part of the cost involved.