Kenne Bell going it!

VegasGT · Oct 7, 2006

Just started the tear down. The blower should be here wednesday. Here is what the car looked like 45 minutes into it.

And this is 3 hours 45 minutes into it. The heater core lines took me 30 minutes to get off, no kidding!

Almost done!:

Dyno from Silver State Motorsports (SSM could not get it to run properly so I drove 240 miles to SPANKIN TIME!):

It made 466/431 at ST Motorsports (SPANKIN TIME). After Adam got his hands on it the car drove beautiful and even though his dyno showed less power than the one here in Vegas at SSM, the car felt faster.

bigcat · Oct 7, 2006

are you going to do a write up on the install?

what was the trouble with the heater hoses?

VegasGT · Oct 7, 2006

bigcat said:
are you going to do a write up on the install?

what was the trouble with the heater hoses?

No write up really. I'll take pics though. The heater hoses have a very unique clip holding them on. You have to get the bottom of the clip to click into place and then as you release pressure from the bottom of the clip you have to push the top of the clip while pulling back. If you try to push both ends of the clip at once it will not work. Strange deal, it really took me 30 minutes to get both lines off.

cLeAnRaCiNgLdR · Oct 8, 2006

I envy you... include pics/vids moneybags.

A&B 06GT · Oct 9, 2006

WOOHOO MORE PICS!!!

donnyonee · Nov 1, 2006

hey vegas gt!
wheres that awesome vette now?
no numbers from adams but sure pulls better. had a couple of situations he worked thru and it got late. i have a couple of mods to do then ill take it back. you goin to his dyno day?

don

wotfr · Nov 2, 2006

But Mom, I Want One To

Which Kenne Belle are you going with, there are what three sizes now 2.2, 2.4, and 2.8 (in Liters of displacement)? Are you gonna turn it up w/ water/methanol injection or just run premium and retard timing? I keep telling myself I wanna go the N/A route, but that is just my logical side telling my lead foot 'No we can't afford it'(boost). Please keep us posted on the install, and enjoy all that neck-snapping torque you are headed for.

VegasGT · Nov 2, 2006

donnyonee said:
hey vegas gt!
wheres that awesome vette now?
no numbers from adams but sure pulls better. had a couple of situations he worked thru and it got late. i have a couple of mods to do then ill take it back. you goin to his dyno day?

don

Haha! Ya I caught him up here in Vegas and we spent an hour or so driving around the streets of Vegas with his laptop in hand getting my car tuned a little more.

Maybe going to the dyno day.

VegasGT · Nov 2, 2006

wotfr said:
Which Kenne Belle are you going with, there are what three sizes now 2.2, 2.4, and 2.8 (in Liters of displacement)? Are you gonna turn it up w/ water/methanol injection or just run premium and retard timing? I keep telling myself I wanna go the N/A route, but that is just my logical side telling my lead foot 'No we can't afford it'. Please keep us posted on the install, and enjoy all that neck-snapping torque you are headed for.

I am running the 2.4 Kenne Bell. Torque? you bet! Ya meth is a good idea but at this point I am going to build a shortblock first before I add anymore power. I want a 15PSI street car. Something around 550rwhp or so. Its only money right? Heck with the power I have now my clutch is shot and I only have maybe a week with the blower on it.

racegirl1 · Nov 3, 2006

Hi VEGASGT

What PSI are you running from Kennebell? Did you also get the intercooler? What was your mustangs base line prior to putting on the KB? What other additional mods do you have on the car?

481 RWHP is huge....I also have the KB 2.4 with 8 PSI with aftermarket exhaust, stock cats, heads. But I'm not getting nearly that kind of RWHP. I'm also using KB canned tune with the rev limiter curve set at 6,200 RPM

That's why I want to know what you have done to your car as far as extra modifications go.

Thanks

VegasGT · Nov 3, 2006

racegirl1 said:
Hi VEGASGT

What PSI are you running from Kennebell? Did you also get the intercooler? What was your mustangs base line prior to putting on the KB? What other additional mods do you have on the car?

481 RWHP is huge....I also have the KB 2.4 with 8 PSI with aftermarket exhaust, stock cats, heads. But I'm not getting nearly that kind of RWHP. I'm also using KB canned tune with the rev limiter curve set at 6,200 RPM

That's why I want to know what you have done to your car as far as extra modifications go.

Thanks

I am running 10 psi, 60lb injectors (so I can grow into them), axle back exhaust, Kenne Bell cooler. Rev limiter set at 6500rpm. My car ran 481/423 on a Vegas Dynojet and 466/431 on a California Dyno Jet.

All I know is I need more power, a 420rwhp Z06 just pulled 3 car lengths on me from 40-145mph, on a closed course

Hatchman · Nov 15, 2006

Looks good! What kind of intercooler reservoir are you using? Did it come with the powersteering relocation bracket?

VegasGT · Nov 15, 2006

Hatchman said:
Looks good! What kind of intercooler reservoir are you using? Did it come with the powersteering relocation bracket?

The reservior is an aftermarket piece for a '03 '04 Cobra, I just made a bracket to work. The powersteering reservior bracket I made from 2" flat stock aluminum.

Kenne Bell going it!

VegasGT

New Member

bigcat

start with the upper hole, and if more traction is

VegasGT

New Member

cLeAnRaCiNgLdR

New Member

A&B 06GT

New Member

donnyonee

New Member

wotfr

New Member

VegasGT

New Member

VegasGT

New Member

racegirl1

New Member

VegasGT

New Member

Hatchman

New Member

VegasGT

New Member

Similar threads

Kenne Bell going it!

New Member

start with the upper hole, and if more traction is

New Member

New Member

New Member

New Member

New Member

New Member

New Member

New Member

New Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency