• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Kill switch wiring

  • Thread starter Thread starter Jack's95gt
  • Start date Start date Oct 2, 2007
J

Jack's95gt

Member
Aug 15, 2004
443
1
18
Huntingdon Valley, PA
Oct 2, 2007
#1
  • Oct 2, 2007
  • #1
I'm moving my battery to the hatch area with a Taylor box and kill switch. I bought a single pole kill switch and I trying to think how to make it work. Can it may possibly work with a relay?
 

Fett

New Member
Nov 2, 2004
766
6
0
Oct 2, 2007
#2
  • Oct 2, 2007
  • #2
Pardon my ignorance, but what is a one pole kill switch? In order for it to be a cutoff switch, doesn't it need to be two pole?
 
J

Jack's95gt

Member
Aug 15, 2004
443
1
18
Huntingdon Valley, PA
Oct 3, 2007
#3
  • Oct 3, 2007
  • #3
Two pole top and one pole bottom.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 4, 2007
#4
  • Oct 4, 2007
  • #4
You bought the wrong kind of switch if you want to shut off the alternator properly.

For a battery cut off switch, see http://www.moroso.com/catalog/categorydisplay.asp?catcode=42225
is the switch http://www.moroso.com/catalog/images/74102_inst.pdf is the installation instructions.
Use the super duty switch and the following tech note to wire it and you will
be good to go.

Use the Moroso plan for the alternator wiring and you risk a fire. The 10
gauge wire they recommend is even less adequate that the stock Mustang
wiring.

There is a solution, but it will require about 40' of 18 gauge green wire.

Wire the battery to the two 1/2" posts as shown in the diagram.

The alternator requires a different approach. On the small alternator plug
there is a green wire. It is the sense lead that turns the regulator on when
the ignition switch is in the run position. Cut the green wire and solder the
40' of green wire between the two pieces. Use some heat shrink to cover the
splices. See http://fordfuelinjection.com/?p=7 for some excellent
help on soldering & using heat shrink tubing.

Run the green wire back to the Moroso switch and cut off the excess wire.
Try to run the green wire inside the car and protect it from getting cut or
chaffed. Crimp a 18 gauge ring terminal (red is 18 gauge color code for the crimp
on terminals) on each wire. Bolt one ring terminal to each of the 3/16" studs.
Do not add the jumper between the 1/2" stud and the 3/16" stud as shown it the
Moroso diagram.

How it works:
The green wire is the ignition on sense feed to the regulator. It supplies a turn
on signal to the regulator when the ignition switch is in the Run position. Turn the
Moroso switch to off, and the sense voltage goes away, the voltage
regulator shuts off and the alternator quits making power.

The fuse & wiring in the following diagram are for a 3G alternator. The stock alternator uses a dark green fuse link wire that connects to 2 black/orange wires. Always leave them connected to the starter solenoid even if you have a 3G alternator.



See the following website for some help from Tmoss (diagram designer)
& Stang&2Birds (website host) for help on 88-95 wiring
http://www.veryuseful.com/mustang/tech/engine/ Everyone should bookmark this site.

Ignition switch wiring
http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

Fuel, alternator, A/C and ignition wiring
http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

Complete computer, actuator & sensor wiring diagram for 88-91 Mass Air Mustangs
http://www.veryuseful.com/mustang/tech/engine/images/88-91_5.0_EEC_Wiring_Diagram.gif

Vacuum diagram 89-93 Mustangs
http://www.veryuseful.com/mustang/tech/engine/images/mustangFoxFordVacuumDiagram.jpg

Rear mounted battery ground wiring. Follow this plan and you will have zero
ground problems.


One 1 gauge or 1/0 gauge wire from battery negative post to a clean shiny spot
on the chassis near the battery. Use a 5/16” bolt and bolt it down to make the
rear ground. Use a 1 gauge or 1/0 gauge wire from the rear ground bolt to a clean
shiny spot on the block.

One 4 gauge wire from the block where you connected the battery ground wire to
the chassis ground where the battery was mounted up front. Use a 5/16” bolt
and bolt down the 4 gauge engine to chassis ground, make sure that it the metal
around the bolt is clean & shiny. This is the alternator power ground.




The computer has a dedicated power ground wire with a cylindrical quick connect
(about 2 ½”long by 1” diameter. It comes out of the wiring harness near the
ignition coil & starter solenoid (or relay). Be sure to bolt it to the chassis ground
in the same place as you bolted the alternator power ground. This is an
absolute don’t overlook it item for EFI cars

Note: The quick disconnect may have fallen victim to damage or removal by
a previous owner. However, it is still of utmost importance that the black/green
wires have a high quality ground..

Picture courtesy timewarped1972


Crimp or even better, solder the lugs on the all the wire. The local auto stereo
shop will have them if the auto parts store doesn't. Use some heat shrink tubing
to cover the lugs and make things look nice.
 
J

Jack's95gt

Member
Aug 15, 2004
443
1
18
Huntingdon Valley, PA
Oct 21, 2007
#5
  • Oct 21, 2007
  • #5
I have my kill switch wired up as shown in the diagram as in the previous post. I started the car and threw the kill switch to the off position and it still ran. The green/red alternator wire is now switched between the two smaller terminals on the kill switch. I have a 3g alternator upgrade. My yellow/white wire goes to the starter solenoid. Should I try switching the yellow/white instead of the green/red wire??
 
J

Jack's95gt

Member
Aug 15, 2004
443
1
18
Huntingdon Valley, PA
Oct 22, 2007
#6
  • Oct 22, 2007
  • #6
bump
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 22, 2007
#7
  • Oct 22, 2007
  • #7
Do you have the Moroso 74102 switch or another model switch? Only the Moroso 74102 switch will turn off the alternator properly.
 
J

Jack's95gt

Member
Aug 15, 2004
443
1
18
Huntingdon Valley, PA
Oct 23, 2007
#8
  • Oct 23, 2007
  • #8
I used the Taylor 1033 switch which has four terminals on the back. It looks identical to the Moroso 74102. I believe that one company or the other must make them for both and labels them with the private brands.

Anyway I cut and yellow/white and tied that into the kill switch and soldered the green/red wire back together gave it a try. The engine cut right off. Since the yellow/white is a larger gauge, I ran a pair of 10 gauge whites back to the switch.
 

Fett

New Member
Nov 2, 2004
766
6
0
Oct 23, 2007
#9
  • Oct 23, 2007
  • #9
Oh, I see now. I have a one pole switch that I am only connecting the positive battery cable to. When I go to the track I will just unplug my alt for tech.

Yea, I know it isn't the proper way to do it...but the only reason I am moving my battery is to make room for some wiring I am doing and my MSD box, and the only reason I am putting a shutoff switch on is to pass tech.
 
You must log in or register to reply here.

Similar threads

D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
207
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
Resolved Wiring electric fan
  • cbac89
  • Aug 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
237
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
cbac89
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
405
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
T
Electrical Brown Connector #31
  • ta66
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
220
Fox 5.0 Mustang Tech Jul 30, 2026
ta66
T
Electrical Where to wire in a kill switch besides fuel pump relay
  • AnthonyA1234
  • Nov 7, 2024
  • Fox 5.0 Mustang Tech
Replies
13
Views
1K
Fox 5.0 Mustang Tech Nov 10, 2024
Bullitt347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?