Lakewood Scattershield Questions

66P51GT

New Member

Nov 7, 2003

721

1

0

Cerritos, CA

Aug 30, 2004

#1

• Aug 30, 2004

• #1

I went to the Pomona swap meet this weekend and couldn't pass up a deal. I was only looking for a billet flywheel and found one. But it was connected to a centerforce clutch pack and included a Lakewood Scattershield.

This will mount behind a roller 306 with a T-5 (Z) using Mustang Steve's cable clutch setup. I also have a set of Mac long tubes.

First, has anyone installed the scattershield in a 65/66? If so, did you have any clearance issues with headers? If so, what brand were they.

Thanks,
-Chuck

 

1320stang

Founding Member

Nov 13, 1998

4,329

23

89

Edmond, Oklahoma

Aug 30, 2004

#2

• Aug 30, 2004

• #2

Do you have the right balance flywheel to go with the motor?

I have a scattershield in my '65 coupe and had to trim the flange on the driver's side. I had Hooker Super Comps.

 

66P51GT

New Member

Nov 7, 2003

721

1

0

Cerritos, CA

Aug 30, 2004

#3

• Aug 30, 2004

• #3

I have both 28oz. and 50oz. billet steel flywheels. I purchased the 50oz. for the roller motor I'm building over the weekend. I originally bought the 28oz. thinking I'd rebuild my 289 but couldn't pass up a 5.0 with a nice Crane cam for $100.

 

G

gp001

Founding Member

Jun 30, 2001

4,401

0

66

So. Cal.

Aug 30, 2004

#4

• Aug 30, 2004

• #4

I have a Lakewood scattershiled and Flowtech full length headers. I did have to grind some of the flange off in 2 or 3 spots

 

6

6stang8

New Member

Dec 5, 2003

28

0

0

Aug 31, 2004

#5

• Aug 31, 2004

• #5

I have Hedman long tubes on my '68, and had to grind the Lakewood T5 bellhousing on the driver's side as well.(I used a dremel and it took forever!! My brother said a grinder would've worked better except I didn't have one.)

I didn't have to grind anything off of the passenger side although I did have the passenger side header off of the car when I installed the Lakewood.

I'm not sure I could have installed the Lakewood bellhousing without having one header or the other removed.

If that turns out to be the case, install the starter in the bellhousing before you install the passenger side header. It's easier to install the top bolt to the starter that way well at least it is with the Hedman's anyway.

You might want to run a tap in the threads of the bellhousing if the bellhousing is new to remove any paint in the threads too.

Edit: I've got a 302 FWIW.

 

66P51GT

New Member

Nov 7, 2003

721

1

0

Cerritos, CA

Aug 31, 2004

#6

• Aug 31, 2004

• #6

6stang8
The bellhousing is used. I'll take your advice and chase the threads before installation. I have a grinder so that isn't a problem.

Thanks all for the info.
-Chuck

 

1320stang

Founding Member

Nov 13, 1998

4,329

23

89

Edmond, Oklahoma

Aug 31, 2004

#7

• Aug 31, 2004

• #7

My notch in my bell was made before I bought it (used) and was made with a smoke wrench . I cleaned it up with a grinder, if I remember right, its about a 3"-4" section about 7 to 8 o'clock if your looking towards the front of the car.

I agree about putting the starter in before the passenger header. I think I put the drivers side in then put in the bell. This would make it easiest to see where you need the clearance as I didn't need any on the passenger side either. Plus the driver's side is the bigger PITA with the steering box and the clutch linkage.

 

pabear89

Active Member

Apr 15, 2003

2,126

0

46

High in the Hills of So Ca with the Voices in My H

Aug 31, 2004

#8

• Aug 31, 2004

• #8

Just some extra info from Lakewood,
Make sure that the Shield is Centered with the Crankshaft end.
this will keep from wearing out the pilot bearing or trans input shaft.
Their instructions, I use the Clutch installation tool stuck in place for this.
They have off-set locator pins or you can just remove them and move it as needed.

PB

 

RaSMG

Founding Member

Oct 5, 2002

270

0

0

Central Cali

Aug 31, 2004

#9

• Aug 31, 2004

• #9

or get a McLeod with preindexed runout, won't have to worry about offset dowels .. and they clear my hooker super comps.