• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Loctite for Head Studs ???

  • Thread starter Thread starter socalracer2007
  • Start date Start date Feb 27, 2007
S

socalracer2007

New Member
Feb 23, 2007
7
0
0
Feb 27, 2007
#1
  • Feb 27, 2007
  • #1
I am putting my 1/2" head studs into my R302 block and I was wondering if this is the right stuff to use. I also was wondering if it is okay to use when I tighten my heads down ?

 

Attachments

  • locktite1az1.webp
    2.8 KB · Views: 167
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Feb 27, 2007
#2
  • Feb 27, 2007
  • #2
No... thread sealer for head studs.
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Feb 27, 2007
#3
  • Feb 27, 2007
  • #3
As Daggar said....Get ya some ARP thread sealer and don't worry about it. If you torque them right, they won't come apart no loctite necessary.
 

montegoman351

Member
Jan 12, 2007
169
1
18
Feb 27, 2007
#4
  • Feb 27, 2007
  • #4
That's what I used on my Cleveland, but for you on a 302 block where the studs go so near the water passages, get some ARP thread sealer, or some good Teflon thread sealer.
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Feb 27, 2007
#5
  • Feb 27, 2007
  • #5
Permatex blue (loctite) is also correct for use with head studs that pass through water jackets. It was specified by TFS when I installed my heads, using ARP studs.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Feb 27, 2007
#6
  • Feb 27, 2007
  • #6
The problem with the loctite is that it's pretty runny. You cannot be assured of the same seal that you'll get with thread sealer.

I've not tried the blue loctite in the paste form for water tight bolts yet. It seems though, that it would be better for that application than the tube.
 

montegoman351

Member
Jan 12, 2007
169
1
18
Feb 27, 2007
#7
  • Feb 27, 2007
  • #7
I used a dab of red on mine when I studded my heads.
 
You must log in or register to reply here.

Similar threads

Engine Felpro 9333 pt1 (with 8psi boost)
  • JD1964
  • Jan 14, 2026
  • Fox 5.0 Mustang Tech
Replies
18
Views
1K
Fox 5.0 Mustang Tech Feb 1, 2026
Qtrhrse23
Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
748
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
G
Resolved Smoking Wiring Issue After GT40 Head Swap
  • Grapes
  • Aug 15, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
607
Fox 5.0 Mustang Tech Aug 22, 2026
Grapes
G
G
Engine Pushrod Length Question
  • germain101
  • Sep 22, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
761
Fox 5.0 Mustang Tech Sep 25, 2025
Noobz347
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?