• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

%-lug Conversion Questions??

  • Thread starter Thread starter 808Gt
  • Start date Start date Dec 31, 2005

808Gt

Founding Member
Apr 21, 2002
115
0
16
Hawaii
Dec 31, 2005
#1
  • Dec 31, 2005
  • #1
I am planning on buying rims for my car soon, Kazera KZ-A 17x7.5....

I am planning on just doing the rear first, PLanning on buying the rear kit with the stock drum breaks, and i wanted to know if I would have to change the MC if I just do the rears only?? Also would I have to buy the seal kit for the rears??
Give me any input you have.....New to this but been reading for awhile now on the conversion.........
 

TrunkFunk

Banned
Dec 28, 2005
83
0
0
A1A - Beach Front Avenue ...
Dec 31, 2005
#2
  • Dec 31, 2005
  • #2
I'll assume you are referring to a 5 lug, not a percentage lug conversion.
Based on your screenname you own an 88 GT, right?

The Ford axle and drum kit ($200) for the rear is commonly referred to as the Ranger axle & drum 5-lug swap. It's the same thing as pulling axles and drums off of a Ford Ranger. You save a trip to the junkyard and you get new parts by buying the $200 kit though.

This "Ranger" setup retains the same track width dimensions as your stock 4-lug Mustang axles have. With a 7.5" wide wheel you will want about zero offset for the rear wheels and if you do the "Lincoln" rotor swap for the front you will want about a +12 offset wheel in the 7.5" width variety. Make sure these wheels have the proper center hub bore to mount as well.

You don't need to change the master cylinder and you should probably replace the axle seals on the ends of the rear end while you're in there ... just because they are only about $3-4 a piece (mainland price).
 

808Gt

Founding Member
Apr 21, 2002
115
0
16
Hawaii
Dec 31, 2005
#3
  • Dec 31, 2005
  • #3
yea i ment the 5lug conversion

hmmmm, the offsets need to be zero in the back? and the fronts +12mm..... here are the wheels that im going to buy, http://www.tirerack.com/wheels/Disp...lModel=KZ-A&wheelFinish=Flat+Black+w/Mach+Lip
bt i told my friend to see if he can get them n 17" with 15mm offset...... i was planning on doing was buying the rear kit then buying the front at a junkyard, which i know i would have to change MC and prop. valve.. how would i knw if these have the proper center hub bore to mount as well??


Also what is the stock offset for an 87 mustang, just wanted to knw....

thanks by the way for answering my Q's
 

bubba-dough

Active Member
Dec 28, 2004
1,044
2
38
Indiana
Dec 31, 2005
#4
  • Dec 31, 2005
  • #4
Just to second what was said above, no you would not need to change the mc. And yes I would change the axle seals as well as the axle bearings.
 

808Gt

Founding Member
Apr 21, 2002
115
0
16
Hawaii
Jan 1, 2006
#5
  • Jan 1, 2006
  • #5
HAPPY NEW YEAR to all.....
--------------------------------------------------------------------------
Had some Q's....
The rims that I am getting are 15mm offset, got that from Tirerack..... But i wanted to knw if it was ok if i can use this offset in the fronts when I change to the 94-95 mustang hud/spindel rotors?? would they stick out or be in??? Or if i should just use a 25-26mm offset??


Sorry for all the q's again, NEED HELP, just dont want to mess things up and i dont want to buy a spacer and what not.......
 

TrunkFunk

Banned
Dec 28, 2005
83
0
0
A1A - Beach Front Avenue ...
Jan 1, 2006
#6
  • Jan 1, 2006
  • #6
The SN95 spindle, hub and rotor setup will increase the front track .25" per side (1/2" total track increase over stock).

The +15mm offset on the wheels will work great up front with SN parts and will bring the wheels about dead even with the fender lips.

If you run +15 on the rear also I suggest buying longer studs to press into the 5-lug axles and then buying .50" wheel spacers to "untuck" the wheels (for appearance reasons). Or switch to SN length axles and disc setup.

What you need is as easy as using a tape measure on your car.
Measure the fit issues and then do the math.

http://www.rsracing.com/tech-wheel.html
 

808Gt

Founding Member
Apr 21, 2002
115
0
16
Hawaii
Jan 1, 2006
#7
  • Jan 1, 2006
  • #7
Kool thanks TrunkFunk....
K, if i get the SN95 axles can i re-use the drum brakes?? or i have to switch to disc....I think i knw the answer, jus wanna make sure.... Also if i just do the rear first will i have to change the MC..... I was wondering about the proportioning valve, can i just buy the Willwood prop valve??......


thanks again....
 

TrophyHead

15 Year Member
Mar 18, 2003
1,195
11
49
PA
Jan 1, 2006
#8
  • Jan 1, 2006
  • #8
808Gt said:
Kool thanks TrunkFunk....
K, if i get the SN95 axles can i re-use the drum brakes?? or i have to switch to disc....I think i knw the answer, jus wanna make sure.... Also if i just do the rear first will i have to change the MC..... I was wondering about the proportioning valve, can i just buy the Willwood prop valve??......


thanks again....
Click to expand...


Your gonna need to upgrade your MC if you switch to rear disc. With those wheels I would defentaly use either SN95 axels or Lincoln axels. Lincoln axels are a little longer than SN95 but look good on a 8" wide wheel IMO. Alot of people hate the look of Lincoln axels.

http://svo73mm.cjb.net/

I dont know if you can use SN95 axels and a ranger/aerostar 5 lug drum brake set-up?
 
You must log in or register to reply here.

Similar threads

S
Brakes 80 Mustang 4.2 rear chassis brake line for 5 lug conversion!
  • StangPowerLSX510
  • Aug 6, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
185
Fox 5.0 Mustang Tech Aug 9, 2026
limp
5
Brakes ATS brembos and drums
  • 5ptslow
  • Nov 16, 2025
  • Fox 5.0 Mustang Tech
Replies
19
Views
816
Fox 5.0 Mustang Tech Apr 4, 2026
AeroCoupe
8
87 lx 4cyl to v8 project 4 lug disc conversion questions
  • 87lx428
  • Mar 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
631
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 25, 2026
87lx428
8
W
Front ATS brakes with Taurus rear brakes. Full parts needed?
  • Wagonized
  • Sep 24, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
295
Fox 5.0 Mustang Tech Sep 25, 2026
General karthief
R
Fox Hydroboost conversion/proportional valve
  • RubyRedNotch
  • Jul 20, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
0
Views
126
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 20, 2026
RubyRedNotch
R
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?