MAC ProChamber

TorchRed04GT

Member

Nov 28, 2004

56

0

6

MI

Apr 7, 2005

#1

• Apr 7, 2005

• #1

I am thinking about getting a ProChamber and some flows. What will I need to install the ProChamber, what kind of mils should I get?

I was thinking about getting the 40 series orignals, with the prochamber, will this be too loud?

will the drone be unbearable?

Sorry for all the questions

Thanks.

 

98stangv8

Active Member

Oct 3, 2003

1,036

0

36

fayetteville, nc

Apr 7, 2005

#2

• Apr 7, 2005

• #2

TorchRed04GT said:

I am thinking about getting a ProChamber and some flows. What will I need to install the ProChamber, what kind of mils should I get?

I was thinking about getting the 40 series orignals, with the prochamber, will this be too loud?

will the drone be unbearable?

Sorry for all the questions

Thanks.

Click to expand...

pm me...I just took my mils off since I got it programmed into my chip...yours for cheap..

 

myponyrocks

I have more billet on the Stang than most women ha

Apr 18, 2004

1,219

0

37

Apr 7, 2005

#3

• Apr 7, 2005

• #3

I have the catted PC, even though it sounded awesome with flows, it wasnt loud enough for me. I switched to SLP cat-back and OMG! I dont think it would sound as good with a O/R PC, and I think the flows would have suited me fine if they had been just a tad louder. My setup now is just plain obnoxious.

 

TorchRed04GT

Member

Nov 28, 2004

56

0

6

MI

Apr 7, 2005

#4

• Apr 7, 2005

• #4

Will I need o2 Extention wires? Or are the stock ones long enough

 

myponyrocks

I have more billet on the Stang than most women ha

Apr 18, 2004

1,219

0

37

Apr 7, 2005

#5

• Apr 7, 2005

• #5

with the catted PC the stock wires were more than long enough. But I was assuming you are going with the O/R? I dont have access to a lift, I paid to have mine installed... so not sure what they needed as far as tools and gaskets.

 

Gunfighter

Founding Member

Nov 30, 1999

186

0

0

Grapevine, TX

Apr 7, 2005

#6

• Apr 7, 2005

• #6

ProChamber + Flowmasters =

 

xlilzeex

New Member

Aug 2, 2004

45

0

0

Macomb, MI

Apr 7, 2005

#7

• Apr 7, 2005

• #7

.. i have the american thunder catback with the prochamber.. sounds great

 

MustangThief

Founding Member

Nov 7, 2001

331

0

0

Cleveland, Ohio

Apr 7, 2005

#8

• Apr 7, 2005

• #8

Read my sig, and believe me when i say this, my car is actually really quiet for having LONG tubes and NO cats... everyone i tell that i have no cats and long tubes they hardly believe it.... i like it though... it has real TONE and it's not overly loud

 

S

spikeGT_99

New Member

May 3, 2004

184

0

0

Jackson, Ms

Apr 7, 2005

#9

• Apr 7, 2005

• #9

just fyi the pc sounds great with just the stock mufflers still attached i get asked what kind of mufflers i got on there all the time

 

SteedaQ400

New Member

Jan 15, 2003

60

0

0

Austin,TX

Apr 8, 2005

#10

• Apr 8, 2005

• #10

I just put mine on friday and cant get enough of it. It just sounds awesome with the 2 chambers. Heads will turn everywhere you go and you will get good compliments on your exhaust. Go for it

 

mity2

I like Pro3 and all I got was this crappy CT.

Jul 24, 2003

2,872

3

48

StateCollege PA

Apr 8, 2005

#11

• Apr 8, 2005

• #11

u'll love PC

 

propellerhead

New Member

Apr 13, 2004

1,541

0

0

"but what's with the but shots?"

Apr 8, 2005

#12

• Apr 8, 2005

• #12

I have a few Prochamber installation notes in my Cardomain thing. See sig.

 

TorchRed04GT

Member

Nov 28, 2004

56

0

6

MI

Apr 8, 2005

#13

• Apr 8, 2005

• #13

Bump , will I need the o2 extenders, with the o/r pc?

 

propellerhead

New Member

Apr 13, 2004

1,541

0

0

"but what's with the but shots?"

Apr 8, 2005

#14

• Apr 8, 2005

• #14

TorchRed04GT said:

Bump , will I need the o2 extenders, with the o/r pc?

Click to expand...

On a 2004, yes.

 

TorchRed04GT

Member

Nov 28, 2004

56

0

6

MI

Apr 8, 2005

#15

• Apr 8, 2005

• #15

Thanks, also how do you remove the stock studs on the drivers side manifold, and how do the ones from napa go in? Sorry for all the questions.

 

0

04 DSG GT

New Member

Aug 18, 2004

2

0

0

Apr 8, 2005

#16

• Apr 8, 2005

• #16

On an 04 You will need o2 extensions.

 

propellerhead

New Member

Apr 13, 2004

1,541

0

0

"but what's with the but shots?"

Apr 8, 2005

#17

• Apr 8, 2005

• #17

TorchRed04GT said:

Thanks, also how do you remove the stock studs on the drivers side manifold, and how do the ones from napa go in? Sorry for all the questions.

Click to expand...

They'll spin right out. You might have to grab them with pliers or a Vise Grip. Just don't grab the threads or you might dork them up.

 

TorchRed04GT

Member

Nov 28, 2004

56

0

6

MI

Apr 8, 2005

#18

• Apr 8, 2005

• #18

propellerhead said:

They'll spin right out. You might have to grab them with pliers or a Vise Grip. Just don't grab the threads or you might dork them up.

Click to expand...

Thanks again, also do I use the metal sleve that comes with prochamber even if I change out the studs?

 

propellerhead

New Member

Apr 13, 2004

1,541

0

0

"but what's with the but shots?"

Apr 8, 2005

#19

• Apr 8, 2005

• #19

TorchRed04GT said:

Thanks again, also do I use the metal sleve that comes with prochamber even if I change out the studs?

Click to expand...

I can't say yes or no with 100% certainty. From what I've read on here earliers, it's one or the other. The NAPA stud kit, or the metal sleeve.

Try it without the metal sleeve first. See how it seats. If it looks like the mating surfaces bottom out, then maybe it needs the sleeve.

 

TorchRed04GT

Member

Nov 28, 2004

56

0

6

MI

Apr 9, 2005

#20

• Apr 9, 2005

• #20

If I order the PC from partshopper, will I be getting the sliver one or the black coated one?

The pic on partshopper is the sliver one but I thought they don't make the sliver one anymore.