• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Mass air conversion Prolbems PLease help!

  • Thread starter Thread starter Bmatlock
  • Start date Start date Oct 13, 2005
B

Bmatlock

New Member
Jul 24, 2005
5
0
0
Bradley Illinois
Oct 13, 2005
#1
  • Oct 13, 2005
  • #1
just did a mass air conversion on my 1988 GT Vert AOD. The parts came out of a 1989 GT Vert 5-speed. I replace the harness the computer A9L onto my car (Thats what was in the car when I got it should of been a A9P) but any way. It is all stock execpt the C/L meter with clear tube. I thas a H-pipe and flowmasters. It seems to have run better with the speed denisty stuff. I have no power when I start driving and sounds like chug chug missing but it's not. On top end it'd fine all the way to 95+. The timing is set at 10-14 degrees. Map vaccum is unplugged and vac line is blocked off.

I pulled the codes (67, 67, 63, 66, 36 in that order just tonight again) and I replace the MAF meter today (code66) with a new one and made no difference. I even pull the C/L meter and installed the stock housing back on made a beter difference. I am lost. I clean the Idle air motor and housing , EGR. It just seems to run like *****. I need help. So any of you motor gurus out there give me a hand. I am lost..

Brian
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Oct 14, 2005
#2
  • Oct 14, 2005
  • #2
If you are still getting a code 66, I would look very closely at the Mass Air wiring. It sounds like something didn't quite get wired up correctly.

MASS air conversion instructions from http://www.stangnet.com/tech/maf/massairconversion.html FREE

Code 63 - Throttle Position Sensor (TPS) signal too low TPS. Vref missing (5 volt reference voltage supplied by the computer), bad connections or damaged wiring, TPS sensor failed, TPS sensor way out of adjustment. Use a DVM to check for 5 volts on the Orange wire. If it is missing, look for +5 volts at the Orange wire on the EGR or MAP sensor located on the firewall near the center of the car.

Here’s a TPS tip I got from NoGo50…

When you installed the sensor make sure you place it on the peg right and then tighten it down properly. Loosen the back screw a tiny bit so the sensor can pivot and loosen the front screw enough so you can move it just a little in very small increments. I wouldn’t try to adjust it using marks. Set it at .97v-.99v, the closer to .99v the better. Just don’t go over .99, or you upset the fuel calibration and idle quality will suffer.

(copied from MustangMax, Glendale AZ)

1. Always adjust the TPS and Idle with the engine at operating temp. Dive it around for a bit if you can and get it nice and warm.

2. When you probe the leads of the TPS, do not use an engine ground, put the ground probe into the lead of the TPS. You should be connecting both meter probes to the TPS and not one to the TPS and the other to ground.

3. Always reset the computer whenever you adjust the TPS or clean/change any sensors. I just pull the battery lead for 10 minutes.

4. Check the procedure for your year, on my 90 I have to turn the idle screw until it just touches the tab, then insert a .010 feeler gauge and give it about one more turn. Then you adjust the TPS voltage to .98v, reset the computer. Start it up, if the idle is to low then turn the screw in until it is just right, then readjust the TPS voltage to .98v and reset the computer and start it up. The key is to adjust the TPS voltage and reset the computer whenever the idle screw is changed.

Code 66 MAF below minimum test voltage.
Insufficient or no voltage from MAF. Dirty MAF element, bad MAF, bad MAF wiring, missing power to MAF. Check for missing +12 volts on this circuit. Check the two links for a wiring diagram to help you find the red wire for computer power relay switched +12 volts. Check for 12 volts between the red and black wires on the MAF heater (usually pins A & B). while the connector is plugged into the MAF. This may require the use of a couple of safety pins to probe the MAF connector from the back side of it.

There are three parts in a MAF: the heater, the sensor element and the amplifier. The heater heats the MAF sensor element causing the resistance to increase. The amplifier buffers the MAF output signal and has a resistor that is laser trimmed to provide an output range compatible with the computer's load tables.

The MAF element is secured by 2 screws & has 1 wiring connector. To clean the element, remove it from the MAF housing and spray it down with electronic parts cleaner or non-inflammable brake parts cleaner (same stuff in a bigger can and cheaper too).

The MAF output varies with RPM which causes the airflow to increase or decease. The increase of air across the MAF sensor element causes it to cool, allowing more voltage to pass and telling the computer to increase the fuel flow. A decrease in airflow causes the MAF sensor element to get warmer, decreasing the voltage and reducing the fuel flow. Measure the MAF output at pins C & D on the MAF connector (dark blue/orange and tan/light blue) or at pins 50 & 9 on the computer.

At idle = approximately .6 volt
20 MPH = approximately 1.10 volt
40 MPH = approximately 1.70 volt
60 MPH = approximately 2.10 volt

Check the resistance of the MAF signal wiring. Pin D on the MAF and pin 50 on the computer (dark blue/orange wire) should be less than 2 ohms. Pin C on the MAF and pin 9 on the computer (tan/light blue wire) should be less than 2 ohms.

There should be a minimum of 10K ohms between either pin C or D on the MAF and ground.

See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host)

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

http://www.autozone.com/servlet/UiB..._us/0900823d/80/19/59/5a/0900823d8019595a.jsp


Code 67 - clutch not depressed (5 speed) or car not in neutral or park (auto) or A/C in On position when codes where dumped. Possible neutral safety switch or wiring problem. This code may prevent you from running the Key On Engine On tests. You can generally ignore this code, since it has no effect on engine performance.
 
You must log in or register to reply here.

Similar threads

1987 Mustang GT Mass Air Conversion Help
  • mustangmike6996
  • Jan 1, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
2K
Fox 5.0 Mustang Tech Feb 4, 2025
mustangmike6996
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
480
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
A
88 Foxbody Starts but Stalls When Warm Please Help
  • airforcerob
  • Apr 2, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
617
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 4, 2025
Noobz347
Engine Throwing codes 94, 33, 34, 44, and sporadic engine shutoff.
  • Ryu
  • Oct 9, 2024
  • Fox 5.0 Mustang Tech
Replies
13
Views
1K
Fox 5.0 Mustang Tech Sep 13, 2026
Noobz347
B
'03 GT Fuel Pump/Pressure/Delivery Issue
  • Brodach
  • Oct 21, 2025
  • SN95 4.6L Mustang Tech
Replies
8
Views
1K
SN95 4.6L Mustang Tech Oct 31, 2025
gkomo
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?