• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Mass air voltage questions. no .5v reference.

  • Thread starter Thread starter BK_CAULEY
  • Start date Start date Nov 7, 2008
  • 1
  • 2
Next
1 of 2 Next Last

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Nov 7, 2008
#1
  • Nov 7, 2008
  • #1
Ok as the title states i have no reference voltage and to the best of my knowledge i should.

i have traced all wires up into the harness and none are damaged and seem to be in good shape. what could be causing this. The whole problem started when my car started running bad rich. I isolated it to the mass air. when i unplug it with the car idling nothing changes. and the car runs the same with it plugged up as it does when its unplugged.

I measured voltage from left to right starting at tyhe red wire.

First wire: 12v
second: ground
Third: nothing
Fourth: nothing

 

Attachments

  • 110608_201200-1.webp
    7.7 KB · Views: 695

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 7, 2008
#2
  • Nov 7, 2008
  • #2
Tell me if im right? Plug has 5 holes .1 red is power.2 emty 3black lg stripe is power ground.4 tan lb stripe is sig rtn.5 darkblue with org stripe is maf sig.
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 7, 2008
#3
  • Nov 7, 2008
  • #3
How to ck 4 wires.you did the 1st red already. to ck power ground hole 3.use volt meter . Key on connect +to pin 1red than grd to pin3 bk with lg should have 12v if not you start thier .you would use a multimeter to ck ohms on the other 2
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Nov 8, 2008
#4
  • Nov 8, 2008
  • #4
no there is only four spots on it. and i grounded to the body when i checked for the 12v. i will test the ground tommorrow. and shouldnt one of the wires still have a .5v reference going to it. or does the mass air meter send the .5v out.

i am checking all this with the car off key on and with it idling.
 

5.0Droptop

...all those nights we shared, and you're a dude??
Special Agent Mukity-Muck Whats in Charge Round Here
May 15, 2002
1,785
1,130
233
Indiana
Nov 8, 2008
#5
  • Nov 8, 2008
  • #5
I would think the eec would throw a code if you have no return signal??
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Nov 8, 2008
#6
  • Nov 8, 2008
  • #6
5.0Droptop said:
I would think the eec would throw a code if you have no return signal??
Click to expand...

it is. thats why i was checking it. and the fact that my car is dumping so much fuel ive had to change my oil 3 times in two weeks and its only ran about 30 minutes.
 

5.0Droptop

...all those nights we shared, and you're a dude??
Special Agent Mukity-Muck Whats in Charge Round Here
May 15, 2002
1,785
1,130
233
Indiana
Nov 8, 2008
#7
  • Nov 8, 2008
  • #7
Could the MAF electronics be bad and not sending the signal??
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Nov 8, 2008
#8
  • Nov 8, 2008
  • #8
5.0Droptop said:
Could the MAF electronics be bad and not sending the signal??
Click to expand...

i hope not man. its a new anderson meter. literatly 3 months old with hardly any run time. and i think the .5v ref has to be there for it to be able to send a signal.
 

5.0Droptop

...all those nights we shared, and you're a dude??
Special Agent Mukity-Muck Whats in Charge Round Here
May 15, 2002
1,785
1,130
233
Indiana
Nov 8, 2008
#9
  • Nov 8, 2008
  • #9
Im just throwing ideas out there for you to think on. I have not dug into the maf system much.
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Nov 8, 2008
#10
  • Nov 8, 2008
  • #10
I think it goes (not in the exact order tho but has) 12V to power the heating element...a ground...a 5 volt TO the meter and.... a signal return that the 5 volt goes through the element and depending on the air flowing through it changes how much voltage gets through and comes out the output....and should be at least around .5-.7 volts at idle at the output to the ecu.

unplug the meter and probe each wire with the key on and there should be a 12v and a 5v reference voltage.If theres no 5v going TO the meter it's not a bad meter it's a bad wire going to the meter.
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Nov 13, 2008
#11
  • Nov 13, 2008
  • #11
can anyone tell me which wire is suppose to be the .5v reference. i still have it at my tps sensor. i can just tie on there i guess.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Nov 14, 2008
#12
  • Nov 14, 2008
  • #12
MAF doesn't use 5v VREF
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 14, 2008
#13
  • Nov 14, 2008
  • #13
I think it needs to be running .pin test ohms engine off to ck volts needs to be running the 5v if sent back by cycle
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Nov 14, 2008
#14
  • Nov 14, 2008
  • #14
vristang said:
MAF doesn't use 5v VREF
Click to expand...

i figured that out this morning after reading a post on the corral. thanks though. and i think the maf sensor took a crap.
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 14, 2008
#15
  • Nov 14, 2008
  • #15
All i can do is tell u fords pin test dc .other than bat volts all test are ohms .the pcm sends back 5v .it uses 4 wires but harness har 5 holes.i can do a write up of what it says but am i right with wire colors.any cel codes
 

joel5.0

Member
Jun 15, 2004
429
2
18
Puerto Rico
Nov 14, 2008
#16
  • Nov 14, 2008
  • #16
FYI......

 

Attachments

  • MAF_test.gif
    19.3 KB · Views: 6,094

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 14, 2008
#17
  • Nov 14, 2008
  • #17
Any of these codes26,56,66,81?
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 14, 2008
#18
  • Nov 14, 2008
  • #18
I guess 66 pin test dc6 ck continuity of maf signal and vpwr circuits.key off set meter to 200 ohm scale. .unplug pcm unplug mass test pin 50 to maf sig record it than 37 with vpwr record it than57 with vpwr any thing more than 5 ohms indacates a short.if im right with colors i think DB/O is what you where asking 5v but thats when warm and running. That uses jumper wire to test not sure if you can probe wire?
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Nov 14, 2008
#19
  • Nov 14, 2008
  • #19
didnt get a chance to pull the codes tonight. but i swapped my 19's back on with a stock meter and still the same.

i was letting my car idle tonight and unplugged the meter and the car ran exactly the same. what could be causing this? im now getting a 1-1.2 volt on the light blue wire at idle and my ground and positive are fine so now im stumped.
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 14, 2008
#20
  • Nov 14, 2008
  • #20
I did c to rule out a maf in say engine missing ,to rich or you get it .unplug maf and car runs smooth than bad maf .dont rush scan it and go from that .record all codes koeo koer and constant .in my 03 im hooked to predator im 1v to4v while driving
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

8
Engine Dreaded 5v reference
  • 89foxstang
  • Jun 24, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
151
Fox 5.0 Mustang Tech Jun 25, 2026
89foxstang
8
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
387
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
Electrical problem plug in the drivers kick panel
  • Mindseye007
  • Aug 16, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
238
Fox 5.0 Mustang Tech Aug 16, 2026
Mindseye007
8
Electrical Crank-no start ... no spark ... no injector pulse, was it something I did? (redux)
  • 85gtCOBRA
  • Oct 28, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
682
Fox 5.0 Mustang Tech Oct 29, 2025
85gtCOBRA
8
F
2004 Mustang GT – Fuel Pump Not Priming
  • Fayio
  • Apr 22, 2026
  • SN95 4.6L Mustang Tech
Replies
7
Views
542
SN95 4.6L Mustang Tech Apr 27, 2026
n0v8or
N
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?