• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Mustang dies at Highway speeds!!

  • Thread starter Thread starter kylebgt
  • Start date Start date Nov 4, 2007

kylebgt

New Member
Jul 2, 2007
0
0
0
Nov 4, 2007
#1
  • Nov 4, 2007
  • #1
This is really getting on my nerves because of how dangerous it is. Basically, my car will try to kill itself when I push the clutch in and roll to a stop in neutral. I have seen sooo many people complaining about this and all everyone says is "its the IAC" well I replaced that and it is still doing it This CANNOT be good for the engine. When I am coming to a stop the revs will drop and hold at 1k like normal, then down to 700< ok little low but still ok then it will nose dive to 500 and all the way down to 100 at this point the power steering basically shuts off and half the time the engine stalls. If I do come to a stop without it dying the revs will bounce between 100-500 continuesly for about 10 seconds and then eventually find its way back up to 750. What could this be!!!! fuel filter, spark plug wires, mafs???? it is complete and if my car keeps on doing I might be forced to sell it
 

the98stang

Active Member
Aug 12, 2005
2,408
0
47
Clovis, CA
Nov 4, 2007
#2
  • Nov 4, 2007
  • #2
Did you replace it with a motorcraft IAC? Did you reset the PCM? If yes, trying cleaning the MAF.
 

03ghoststang

Well-Known Member
Jul 16, 2005
1,930
1
57
Los Angeles, California
Nov 4, 2007
#3
  • Nov 4, 2007
  • #3
my car did something similar when it was new ended up being a connector by the battery junction box
 

fast97gt

Active Member
Jan 2, 2007
1,082
2
49
north carolina
Nov 4, 2007
#4
  • Nov 4, 2007
  • #4
did you disconnect the battery for a few mins. if you didnt do it, and always do it after and during installing new parts. but i would check the connections on the maf sensor, and clean it with carb cleaner
 

BennyBlown2v

New Member
Dec 9, 2004
1,233
1
0
Carmel, INdiana
Nov 4, 2007
#5
  • Nov 4, 2007
  • #5
fast97gt said:
did you disconnect the battery for a few mins. if you didnt do it, and always do it after and during installing new parts. but i would check the connections on the maf sensor, and clean it with carb cleaner
Click to expand...

They make MAF cleaner, carb cleaner can eat away at the some of the coatings and plastics used in maf sensor assemblies.

I have this same problem with my car...I replaced the IAC with a new ford one, messed with everything I possibly could think of...and still not fixed. My guess is its an IAC tuning issue, one which it seems like a lot of people (modularpowerhouse included...) have trouble tuning out.
 

the98stang

Active Member
Aug 12, 2005
2,408
0
47
Clovis, CA
Nov 4, 2007
#6
  • Nov 4, 2007
  • #6
could be IAC/dashpot tuning issue as well
 

kylebgt

New Member
Jul 2, 2007
0
0
0
Nov 4, 2007
#7
  • Nov 4, 2007
  • #7
Yeah I have disconnected the battery numerous times. Defiantly not a problem with the ECU. I am starting to the that whoever programmed the Engine Control Unit for Ford did a ****ty job and the computer isnt telling the IAC how to function properly. I have searched and searched but cannot find an answer. I think that I may change the fuel filter next, hopefully thats what it is
 
B

[BlackDiamond]

New Member
Sep 19, 2005
119
0
0
Nov 5, 2007
#8
  • Nov 5, 2007
  • #8
I hear a lot about this problem but never had it... why would some people have it and some never?
 

jstreet0204

Active Member
Jun 26, 2003
939
0
36
Winston Salem, NC
Nov 5, 2007
#9
  • Nov 5, 2007
  • #9
There are many things that effect idle problems like this, that is why they are hard to troubleshoot. Fuel trims, IAC, TPS, Battery voltage, vacuum leaks, fuel filter, etc. Datalogging the issue will greatly improve your chances of fixing the problem without throwing parts at it. So if you don't have the ability to do it yourself, you may want to take it to a shop.

On another note, when it happens while rolling, and you lose power steering, just let out on the clutch to start it back up.
 

fast97gt

Active Member
Jan 2, 2007
1,082
2
49
north carolina
Nov 5, 2007
#10
  • Nov 5, 2007
  • #10
BennyBlown2v said:
They make MAF cleaner, carb cleaner can eat away at the some of the coatings and plastics used in maf sensor assemblies.

I have this same problem with my car...I replaced the IAC with a new ford one, messed with everything I possibly could think of...and still not fixed. My guess is its an IAC tuning issue, one which it seems like a lot of people (modularpowerhouse included...) have trouble tuning out.
Click to expand...

i did not know this about the maf cleaner made specifficly for this application think you for correcting me, by the wayive not had this problem yet
 

hotmustang331

Active Member
Apr 29, 2004
2,967
3
48
Bastrop,TX
Nov 6, 2007
#11
  • Nov 6, 2007
  • #11
BennyBlown2v said:
They make MAF cleaner, carb cleaner can eat away at the some of the coatings and plastics used in maf sensor assemblies.

I have this same problem with my car...I replaced the IAC with a new ford one, messed with everything I possibly could think of...and still not fixed. My guess is its an IAC tuning issue, one which it seems like a lot of people (modularpowerhouse included...) have trouble tuning out.
Click to expand...

That shouldnt be hard to take car of. Like 98stang said, it looks like a dashpot tuning issue. Raising the idle RPM for dashpot mode (or inotherwords, while "moving" over XX set MPH) SHOULD take care of this issue. Ill take a look to see exactly what can be done...I havnt opened the PR software in about 3 weeks
 
C

cooper

New Member
Dec 9, 2005
96
0
0
Nov 6, 2007
#12
  • Nov 6, 2007
  • #12
my car did this too. iac , and optima batery change helped some. Do NOT try to clean the MAF or IAC with spray cleaner this will f it up. Im not sure of a fix ,cause my car still some times stoping at a light the rpm's will drop to 400, untill a compleat stop and will regain normal 800-875 idle, but it dosent die .
 
C

Chris00GT

Founding Member
Jan 28, 2001
275
0
16
York Springs, PA
Nov 6, 2007
#13
  • Nov 6, 2007
  • #13
I've seem this problem sometimes being caused by cold air kits. I'd remove it and re-install the stock setup and see if it helps.
 
You must log in or register to reply here.

Similar threads

K
Engine 2000 Mustang GT - Fuel issue post-blown spark plug repair
  • kenster1092
  • Feb 26, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
361
SN95 4.6L Mustang Tech Mar 10, 2026
kenster1092
K
S
1998 Mustang Gt Rattling sound, cannot locate. Video included
  • studerman1
  • Mar 31, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
8
Views
244
1996 - 2004 SN95 Mustang -General/Talk- Apr 1, 2026
studerman1
S
A
Rough idle - cylinder 1 and 6 misfire HELP
  • austindavies935
  • Jul 24, 2025
  • SN95 4.6L Mustang Tech
Replies
12
Views
726
SN95 4.6L Mustang Tech Jul 24, 2025
gkomo
E
2007 GT Stalls when lights or a/c turned on
  • ejscarfo
  • Jun 22, 2026
  • 2005 - 2009 Specific Tech
Replies
2
Views
138
2005 - 2009 Specific Tech Jun 29, 2026
ejscarfo
E
R
What's it Worth? 1997 Cobra, a ton of mods and restoration
  • riored97snake
  • Jun 18, 2026
  • What is it Worth?!?!?
Replies
2
Views
172
What is it Worth?!?!? Jun 21, 2026
riored97snake
R
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?