• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 V6 Mustang Tech

my '00 3.8L has a couple issues, need insight.

  • Thread starter Thread starter 305newedge
  • Start date Start date Jul 5, 2021
3

305newedge

Member
Jul 5, 2021
4
1
13
Boca raton
Jul 5, 2021
#1
  • Jul 5, 2021
  • #1
Hey everyone, hope you guys had a safe 4th of july, I have a 3.8liter v6 2000 new edge which i am the second owner and have had it for about 4 years now.
So I do know about the car a bit by now, it has always been reliable and I changed out nearly everything in the vehicle besides the engine and transmission once i got it though it is all entirely bone stock, practically.

Anyways, sorry for the ramble, about 2 1/2 weeks ago she was super rough on idle, weak throttle response, even harder to crank a bit, the gauge would fluctuate and be in .500 rpm or even lower and it was to the point it was turning off in longer red light stops when i wasnt giving gas to the engine. During this same time, the exhaust or muffler was releasing a distinct noticable noise. Much similar to the noise in youtube videos i have came across of new edge owners (v6 or gt alike) that has a fuel injector problem or such, sounded quite similar to that.

My brother and me put mystery foam through the vaccum line and gas tank and idle was much better and it cleaned out the engine since it released quite a bit of smoke. Acceleration and throttle response was much better as well than before, but still not quite the same, my brother didnt notice much and thought it was fine but im the owner and have daily driven it so I just know my car. In addition, even after the treatment gas mileage still sucks! In the city my '00 would average lets just say atleast 19-20 even if im going at it heavy whereas now its roughly possibly around 12mpg or so.

So i deleted the codes after we put the motor treatment and i drove it around a couple days, now it pops for 3 codes.
P0174 System too lean (bank 2)
P0171 System too lean (bank 1)

And also P0401
although this code in particular popped months ago, i knew i probably had a exhaust leak but didnt have the time to take it to the shop due to work (says exhaust gas recirculation flow insufficient undetected)


My zurich ZR11 reader also had red colors near EGR valve, catalytic converter, o2 sensor, eva, and htn. I just bought the reader and dont know much about it but i think apparently red means somethings up basically.
I got some ev6 fuel injectors here to see if that will solve the issue, the injectors are pretty worn out already and i didnt change them ever so they most likely need replacing and i also have a cheaper coil pack on the way to rule out. I know it cant be the plugs since i just did them or the wires since it cranks and starts everytime.

I was wondering if anyone of you had any insight tips or advice when changing the fuel injectors on this engine as well as those codes in particular. There is not much in youtube about changing injectors on the 3.8l engine
 

RaggedGT

Been here over a DECADE and still no CT
Mod Dude
Jul 20, 2014
4,739
3,188
203
Taylorsville ky
Jul 6, 2021
#2
  • Jul 6, 2021
  • #2
I think it’s pretty common for the egr passages and the tube to get stopped up. I think I’d start there. As far as injectors go,you should be able to disconnect the fuel rail from the fuel line with a quick connect tool- un bolt the rails and gently pry it up and out. Some injectors might stay with the rail-some might stay in the intake. Twist em out and make sure all the pintle caps and o rings are accounted for
 
Reactions: 305newedge
3

305newedge

Member
Jul 5, 2021
4
1
13
Boca raton
Jul 6, 2021
#3
  • Jul 6, 2021
  • #3
RaggedGT said:
I think it’s pretty common for the egr passages and the tube to get stopped up. I think I’d start there. As far as injectors go,you should be able to disconnect the fuel rail from the fuel line with a quick connect tool- un bolt the rails and gently pry it up and out. Some injectors might stay with the rail-some might stay in the intake. Twist em out and make sure all the pintle caps and o rings are accounted for
Click to expand...
Thanks a lot for your input I will definitely check that out then !
 
3

305newedge

Member
Jul 5, 2021
4
1
13
Boca raton
Jul 6, 2021
#4
  • Jul 6, 2021
  • #4
305newedge said:
Thanks a lot for your input I will definitely check that out then !
Click to expand...
Update found out what the issue was one of the stock hoses was completed corroded and one of the vaccum line that connect to the cai coupler was ripped apart as well i dont know how i didnt see that when i put the motor treatment. Rides normal and no codes now
 
Reactions: RaggedGT

Toofastt

New Member
May 21, 2001
3
0
1
Toronto
Jul 27, 2021
#5
  • Jul 27, 2021
  • #5
Glad to hear it got fixed, its not a good feeling when something is wrong with your car
 
You must log in or register to reply here.

Similar threads

L
95 gt engine vibration
  • lenzgt
  • May 11, 2026
  • 1994 - 1995 Specific Tech
Replies
6
Views
213
1994 - 1995 Specific Tech May 26, 2026
lenzgt
L
is my car dead
  • kenzo0315
  • Jun 30, 2025
  • SN95 V6 Mustang Tech
  • 2
Replies
29
Views
1K
SN95 V6 Mustang Tech Jul 8, 2025
kenzo0315
K
Engine 2000 Mustang GT - Fuel issue post-blown spark plug repair
  • kenster1092
  • Feb 26, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
343
SN95 4.6L Mustang Tech Mar 10, 2026
kenster1092
K
R
What's it Worth? 1997 Cobra, a ton of mods and restoration
  • riored97snake
  • Jun 18, 2026
  • What is it Worth?!?!?
Replies
2
Views
161
What is it Worth?!?!? Jun 21, 2026
riored97snake
R
F
Trouble Shooting Sudden Shift of AFR at low RPM
  • Farva_84
  • Jun 6, 2025
  • SN95 4.6L Mustang Tech
Replies
8
Views
487
SN95 4.6L Mustang Tech Jun 8, 2025
Farva_84
F
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 V6 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?