My 410W is here

quickGT · Jan 30, 2006

Well I ordered a 410W from Dyno-Flo and it cam a few days ago. Its a 69 Blockbored .40 over with forged Probe dish pistons and Mahle rings, Eagle 4" 4340 forged crank, Eagle 6.2" 4340 forged H beam rods, King Pro Race rod and main bearings, and ARP main studs. If I use a 64cc head my comp. ratio should be at 9.3:1 correct? Well here are pics of my new motor and progress so far. All I have to do is undo the fuel lines and then pull the motor out.

View attachment 489289
View attachment 489291
View attachment 489293
View attachment 489295

Ill use this thread for my progress.

IntenseBlue · Jan 30, 2006

Nice setup. How is the suspension set up?

bluevenom867 · Jan 30, 2006

Is the blower going on the new motor?

Looks nice!

86bluecobra · Jan 30, 2006

thats sweet. I want to know how that motor stands up because im tossing around the idea of buying from them. What year block did they use? is it a one piece rear main? is it a roller block?

quickGT · Jan 30, 2006

Yes the Procharger is going on. Its a earlier block non roller with a 2 piece seal. Ill let you know how it stands up to big power.

quickGT · Jan 30, 2006

Also my suspension is as follows: 90/10s, 50/50s, full length subframes, Rear air bag drag springs, Mega bite upper and lower arms, 3.55 gear

bluevenom867 · Jan 31, 2006

quickGT said:
Also my suspension is as follows: 90/10s, 50/50s, full length subframes, Rear air bag drag springs, Mega bite upper and lower arms, 3.55 gear

Lol,check your torque boxes if you havent already.

Cause if you dont got reinforcments now,you WILL need them

Rick 91GT · Feb 1, 2006

As far as compression goes how big is the dish in the pistons, or do you know the PT# I can figure it out for you.

86bluecobra · Feb 13, 2006

have you got it all together yet? any updates.

quickGT · Feb 13, 2006

Sorry I havent replied t this thread for a while. Ive been busy and sick and I just started on the car again last night. The 347 is now out and Im getting ready to start on the 410W going in. Rick 91GT the part number on the pistons are 12360(or 4 instead of the 0)-040. I just got my lower intake from UPS today so Im going to pull the heads tomorrow evening and all the other parts I need. I will keep you all posted with pics and such.

pb_paulie_b · Feb 14, 2006

69' block?

quickGT · Feb 14, 2006

Yes Paulie its a 69 block.

Rick 91GT · Feb 14, 2006

Compression Ratio Calculator v2.d

Tuesday, February 14, 2006 12:24 pm

* 410 cid *

Bore Size: 4.040
Gasket Bore: 4.100
Piston Top Land Dia: 4.005
Stroke: 4.000
Connecting Rod Length 6.200
Compression Height: 1.280
Deck Height: 9.500
Ring to Top of Piston 0.250
Gasket Thickness: 0.040
Valve Notches Volume: 19.30
Dome Volume: 0.00
Volume Head: 64.00
-------------------------------------
:COMPRESSION RATIO: 9.657
-------------------------------------

calculation variables:

Piston to Deck: 0.020
Crank Throw: 2.000
Vol. Above Top Ring: 0.91 cc
Piston to Dec Vol.: 4.20 cc
Gasket Volume: 8.65 cc
Volume Clearance: 97.06 cc
Cylinder Volume: 840.26 cc
CID: 410.045

pb_paulie_b · Feb 14, 2006

RICK is the man
quickGT I can't wait to see it all together!

quickGT · Feb 14, 2006

WOW Thanks alot Rick. Paulie is right, YOU ARE THE MAN. Anyway I got the heads and all of the accessories off the my old block. Im waiting on my flywheel, harmonic balancer, gaskets, and all else I have ordered. I do have a question. I know this is a non roller block, what do I have to do to make this a roller block? I would like to use my 1.72 SVO rockers and my rocker support. Im going to have a new cam custom ground and if I need new rockers then no problem. I was told that I could use my rockers but the cam is actually the problem in a non roller block to a roller cam. What do I need to make my block a roller? Im having Ed Curtis do my cam. Could he make me all the part to make my block a roller? Thanks

pb_paulie_b · Feb 14, 2006

All you need are link bar hyd.roller lifters. Crane, Comp, and Crower all make these lifter for that purpose. No block machining is necessary. The only disadvantage to this set up over going with a small base circle cam/spider hold down set up is that you wont be able to remove the lifter without taking off the heads.

quickGT · Feb 15, 2006

Progress. My motor is now out and apart. I have disassembled my 308 ( yes I said 347 earlier, but I found out I was lied to, bore is 4 1/16 and stroke is 3, so thats a 308 right?) Anyway I had severe blow by on the motor and no compression on one cylinder. I thought that a hole was in the piston, but no hole. I think the rings are just cracked all the he!!. I have my new flywheel, harmonic damper, and my 1995 Cobra R lower intake I won of of ebay (which I think its probably only a Lightning lower, but still they are not make any longer). Im waiting on my new distributor, headers, oil pan and oil pump, head bolts, and my gasket kit. They should be here in the next 2 days or less. Heads look P&P but need cleaned up and Im taking that ugly yellow paint off. Well enough rambling here are some pics. Will keep you updated.

View attachment 487120
View attachment 487122
View attachment 487124
View attachment 487125
View attachment 487127
View attachment 487129
View attachment 487131

86bluecobra · Feb 19, 2006

that sucks about being lied to. I have always wondered why there are so many 5.0L running around with 331 or 347 strokers now. geez peeps lie way to much.

86bluecobra · Mar 3, 2006

any updates yet?

quickGT · Mar 3, 2006

Actually 86 there have been some updates but I havent posted them yet. Ive had 2 deaths in my family in the past 2 weeks and its been hectic. Ive got all of my parts in except my cam and pushrods, which those will be in within a couple of weeks. Ive had my heads ported and polished and my valves ground. My lower intake has been ported and polished also. My block has been painted as well as my lower intake and my heads. Im going all black on my heads and block and such so that it will hide dirt better and also my polished valve covers and upper intake and all my other look pretty parts will bling (lol). I am uploading pics here in a minute for the thread. If all goes well, I should have the motor back together and in my car within 2-3 weeks. Here are the pics
View attachment 484984
View attachment 484986
View attachment 484987
View attachment 484988

My 410W is here

quickGT

Member

IntenseBlue

Member

bluevenom867

I will have images of molesting stuffed animals in

86bluecobra

Advanced Member

quickGT

Member

quickGT

Member

bluevenom867

I will have images of molesting stuffed animals in

Rick 91GT

Mustang Master

86bluecobra

Advanced Member

quickGT

Member

pb_paulie_b

quickGT

Member

Rick 91GT

Mustang Master

pb_paulie_b

quickGT

Member

pb_paulie_b

quickGT

Member

86bluecobra

Advanced Member

86bluecobra

Advanced Member

quickGT

Member

Similar threads

My 410W is here

Member

Member

I will have images of molesting stuffed animals in

Advanced Member

Member

Member

I will have images of molesting stuffed animals in

Mustang Master

Advanced Member

Member

Member

Mustang Master

Member

Member

Advanced Member

Advanced Member

Member

Similar threads

Privacy & Transparency

Privacy & Transparency