• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

Need nitrous advice.

  • Thread starter Thread starter damien2003gt
  • Start date Start date May 6, 2004
D

damien2003gt

New Member
Jun 20, 2003
181
0
0
May 6, 2004
#1
  • May 6, 2004
  • #1
Need advice on a nitrous system. I posted in the PA forums but got little response. I want to get a basic dry kit. I'd like to go with dry just in case the car has to go back to the dealer for service (ease of removale) I'd also like to keep the cost of the kit relatively low. I also want it very safe. I'm goin to keep it under a 100 shot. I know I need the safety features like window switch and wot switch. What I'd like to know is the specific kit I should go with and where it cheap. And also any other features I should be looking for.
 
R

Roger_4.6_96

Founding Member
Jul 16, 2002
1,209
0
0
Reno,NV
May 6, 2004
#2
  • May 6, 2004
  • #2
Might check ebay they got some good deals
 

Go HoTO!

New Member
Apr 11, 2004
602
0
0
Mountaintop, PA
May 6, 2004
#3
  • May 6, 2004
  • #3
Check out the Venon-1000!!!!

http://www.venom-performance.com/nf/html/products/v1000/v1000avail.htm#avail3


Very safe! Check out the site as it gets into detail on how it works. Lists for $699, but I know where you can get it for $545 shipped.
 
B

BVille99GT

Member
May 1, 2003
283
0
16
Brownsville TX.
May 6, 2004
#4
  • May 6, 2004
  • #4
NOS has a dry kit for our cars with a rpm switch and all the other supprorting parts, I think it list for $700, and I think that NX also has one.
 

mpcv2000

Active Member
Jul 29, 2002
2,371
0
47
Montreal , Quebec !
May 6, 2004
#5
  • May 6, 2004
  • #5
Damien , this kit looks good clicky !

I'll give you a hand to put it on if you want..
 

GoldnGT

Founding Member
Aug 21, 2002
427
0
0
Birmingham, AL
May 7, 2004
#6
  • May 7, 2004
  • #6
You should just go wet. You will remove the same things either way. Just get an aftermarket inlet pipe and tap into it. if you need to take it to the dealer, just swap inlet pipes and put the original test fitting back into your schrader valve. It took me 20 mins to do the same thing to mine.

Mike
 
You must log in or register to reply here.

Similar threads

Need some camshaft guru advice on power loss from supercharger to nitrous
  • TTSaleen
  • Dec 1, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
18
Views
573
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Dec 29, 2025
revhead347
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
483
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
Progress Thread 91GTstroked 90 7 up convertible build
  • 91GTstroked
  • Apr 18, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
268
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 22, 2026
91GTstroked
H
Forced Induction On3 Turbo Kit- Parts list NEEDED - 302 Stock Motor
  • Hirothecool1
  • Feb 27, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
854
Fox 5.0 Mustang Tech Mar 7, 2026
slow84lx
S
A
Procharger install/prep questions
  • ahratrew
  • Nov 22, 2025
  • SN95 4.6L Mustang Tech
Replies
2
Views
314
SN95 4.6L Mustang Tech Nov 26, 2025
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?