• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

New Problem

  • Thread starter Thread starter beerman1378
  • Start date Start date Apr 8, 2010
B

beerman1378

New Member
Aug 7, 2006
28
0
0
Apr 8, 2010
#1
  • Apr 8, 2010
  • #1
I decided to wash my engine the other day and I may have soaked it a little too much. I started it up the next day after cleaning the engine and noticed the car is "chugging" bit from idle to about 2500rpm. Almost feels like it is starving for fuel at different rpm's. I had a new fuel pump put in a few weeks ago so I know that its not the pump or ccrm. Not only is it running very choppy now but the "service engine soon" light is now on. But sometimes it flashes. I dont have a code machine but any ideas on what I should check??
 

streethorse

15 Year Member
Oct 8, 2005
1,042
6
58
Dallas Texas
Apr 8, 2010
#2
  • Apr 8, 2010
  • #2
You may have got water down in the sparkplug wells. Pull the boots off
and blow the wells out with air, I actually use a leaf blower to dry out any
pooled up water. But you should never aim water water near that area.
 
K

Kilgore Trout

Fried or Broiled ?
10 Year Member
Mar 30, 2005
4,749
95
134
Apr 8, 2010
#3
  • Apr 8, 2010
  • #3
You got water in the plug wells.

If the car came up to full temp the COP most likely got steam-cooked. I used to think no big deal I will drive it and the water will steam out of the wells but it steam-cooks the COPs and destroys them.

The code will tell you what cylinder is misfiring. You can get the COP bench tested at Ford.
 

trombonedemon

Well-Known Member
Jun 25, 2009
1,962
39
59
U.S.A, U.S.A., U.S.A.!
Apr 8, 2010
#4
  • Apr 8, 2010
  • #4
:search: Seriously though, this is a common problem after people decide to run high pressured water over the Electronics in the engine. Just use engine degreaser while the engine is hot to loosen up some the grease and grime and pour water in specific places.
 
B

beerman1378

New Member
Aug 7, 2006
28
0
0
Apr 8, 2010
#5
  • Apr 8, 2010
  • #5
Just pulled the code. Misfire Cylinder #5. Water probably got in the coil pak or plug. I think the cylinders are marked on the block.....but what cyl is 5?
 

streethorse

15 Year Member
Oct 8, 2005
1,042
6
58
Dallas Texas
Apr 8, 2010
#6
  • Apr 8, 2010
  • #6
Driver side nearest radiator.
 
You must log in or register to reply here.

Similar threads

9
1997 gt Starts then dies a few seconds after.
  • 97orange
  • Aug 13, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
230
SN95 4.6L Mustang Tech Aug 17, 2026
97orange
9
S
92 5.0 almost starts
  • Steverino
  • Sep 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
188
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 25, 2026
General karthief
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
500
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
T
Fuel P0193 on a 2003 3.8 v6
  • Treemaster5000
  • Aug 18, 2026
  • SN95 V6 Mustang Tech
Replies
0
Views
92
SN95 V6 Mustang Tech Aug 18, 2026
Treemaster5000
T
M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
434
1996 - 2004 SN95 Mustang -General/Talk- Aug 9, 2026
JohnKay
J
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?