• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

O2 wires in harness wrong color??

  • Thread starter Thread starter turp23
  • Start date Start date Jul 2, 2007

turp23

Member
Jun 4, 2007
73
2
8
Louisiana
Jul 2, 2007
#1
  • Jul 2, 2007
  • #1
I tried testing the wires for my O2 sensors at the computer and one is not the correct color. Number 29 was dark green with pink stripe and measured from .4 to .8 volts. Number 43 was dark blue with a green stripe and measured from 14.1 to 14.3 volts. Either one is bad, or one of the wires is wrong. Any advice?
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Jul 2, 2007
#2
  • Jul 2, 2007
  • #2
How did you decide what color the wires should be?

Ford changed the wire colors over the years, and sometimes didn't wait for the new model year to change color....


My 90GT has 91 wire coloring....


jason
 

turp23

Member
Jun 4, 2007
73
2
8
Louisiana
Jul 3, 2007
#3
  • Jul 3, 2007
  • #3
From wiring diagrams and replies from this board. If they changed the color, then what about the voltage? The readings I got cannot be correct. If they are correct, then one must be bad, right?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 3, 2007
#4
  • Jul 3, 2007
  • #4
The 14 volts is probably the O2 sensor heater voltage, the .4-.8 is the O2 sensor output.

Check the AutoZone wiring diagrams for some more input.

AutoZone wiring diagrams

http://www.autozone.com/servlet/UiB..._us/0900823d/80/16/71/3c/0900823d8016713c.jsp for 79-88 model Mustangs

http://www.autozone.com/servlet/UiB..._us/0900823d/80/19/59/5a/0900823d8019595a.jsp for 89-93 model Mustangs

http://www.autozone.com/servlet/UiB..._us/0900823d/80/1d/db/3c/0900823d801ddb3c.jsp for 94-98 model Mustangs
 
D

Deleted member 87397

Jul 3, 2007
#5
  • Jul 3, 2007
  • #5
Look closer at the wires. I had to look at mine multiple times even with the wiring pinout to find the correct colors. Looking at a pinout diagram would probably be better anyway since the corresponding pin should be correct even if you have a different color wire.
 

turp23

Member
Jun 4, 2007
73
2
8
Louisiana
Jul 4, 2007
#6
  • Jul 4, 2007
  • #6
so if the pins are right, what is the voltage I should be getting? How can one be .8 and another 14v?
 

turp23

Member
Jun 4, 2007
73
2
8
Louisiana
Jul 4, 2007
#7
  • Jul 4, 2007
  • #7
can anyone help me out with the voltage readings?
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Jul 5, 2007
#8
  • Jul 5, 2007
  • #8
turp23 said:
can anyone help me out with the voltage readings?
Click to expand...

jrichker said:
The 14 volts is probably the O2 sensor heater voltage, the .4-.8 is the O2 sensor output.
Click to expand...






 

turp23

Member
Jun 4, 2007
73
2
8
Louisiana
Jul 5, 2007
#9
  • Jul 5, 2007
  • #9
What does that mean? Are they good or bad?
 

turp23

Member
Jun 4, 2007
73
2
8
Louisiana
Jul 6, 2007
#10
  • Jul 6, 2007
  • #10
Ok, lets try it this way. If the O2 sensors are good, what should their voltage be?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jul 6, 2007
#11
  • Jul 6, 2007
  • #11
turp23 said:
Ok, lets try it this way. If the O2 sensors are good, what should their voltage be?
Click to expand...

Here's a tip: the newer the sensor, the more the voltage changes, swinging from as low as 0.1 volt to as much as 0.9 volt. As an oxygen sensor ages, the voltage changes get smaller and slower - the voltage change lags behind the change in exhaust gas oxygen.

When the mixture is rich, there's less oxygen in the exhaust than in the ambient air , so voltage is generated between the two sides of the tip. The voltage is greater than 600 millivolts. Remember rich = more voltage.
 
You must log in or register to reply here.

Similar threads

L
Electrical problems with passenger side downstream o2 sensor
  • Lexiii12
  • Sep 14, 2026
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
0
Views
160
2005 - 2014 S-197 Mustang -General/Talk- Sep 14, 2026
Lexiii12
L
J
Fox Lost all gauge cluster function after Holley Terminator X install (solved)
  • Justin17383
  • Nov 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
272
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Friday at 3:09 PM
2000xp8
A
P0036 P0056 P0137 P0157 2020 Ford Mustang GT
  • AmkoA
  • Jun 16, 2026
  • 2024+ (S650) Mustang -General/Talk
Replies
0
Views
291
2024+ (S650) Mustang -General/Talk Jun 16, 2026
AmkoA
A
Problems after exhaust install and 02 harness
  • djj62478
  • Jul 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
39
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
Resolved 93 Mustang 5.0 - Cranks but does not start
  • dan50
  • Jul 18, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
491
Fox 5.0 Mustang Tech Jul 18, 2026
dan50
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?