• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Oil in my intake....

  • Thread starter Thread starter JerryDaugherty
  • Start date Start date Jun 7, 2005
J

JerryDaugherty

Member
Apr 7, 2005
309
0
16
Near Dallas
Jun 7, 2005
#1
  • Jun 7, 2005
  • #1
Everytime I pull my upper intake (Edelbrock Perf.) I have oil in it. Would this have anything to do with the PCV valve? Also would this oil in my upper intake travel down through and cause detonation at startup? This is the only time there is detonation. About 4 times as soon as I start up but after that there is no more. Im really having a hard time with this. ANY help is greatly appreciated.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 7, 2005
#2
  • Jun 7, 2005
  • #2
what does the detonation sound like? It might not be detonation you are hearing.

blow by (ring seal) can allow some oil to get into the intake.

Good luck.
 
J

JerryDaugherty

Member
Apr 7, 2005
309
0
16
Near Dallas
Jun 7, 2005
#3
  • Jun 7, 2005
  • #3
Sounds like dunk dunk like a coffe can is being tapped on....
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jun 7, 2005
#4
  • Jun 7, 2005
  • #4
sounds more like bottom end knocking, not detonation (I think you would be the only guy in history to get detonation on a cold motor at start up. Detonation usually requires leanness, heat, etc).

Good luck.
 
G

gt90stang

New Member
Dec 7, 2002
568
0
0
Jun 8, 2005
#5
  • Jun 8, 2005
  • #5
My old Edelbrock performer sucked oil like crazy. When I put the Explorer lower on with my KB the oil consumption went way down. The Explorer lower has a huge oil baffle with drain ridges. The Performer has a puny baffle, when I removed my Performer lower I noticed that the baffle was bent such that the oil would run towards to PCV valve. The guy that installed my Performer just slapped the baffle on out of the box.

One thing I did to reduce the consumption was to put a restrictor in the line from the valve cover to the TB that had a 1/16" hole in it. See:

http://geocities.com/dbennettya/Mustang_PCM/restrictor.JPG
http://geocities.com/dbennettya/Mustang_PCM/restrictor_in.JPG

It goes in the tube that connects to the TB.

Don
 
You must log in or register to reply here.

Similar threads

Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
735
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
T
Oil burning on my recently buil 302
  • The blk67
  • May 15, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
250
Fox 5.0 Mustang Tech May 15, 2026
Noobz347
Brakes Front Brake Hardline Routing
  • 93Nifty
  • Sep 11, 2026
  • Fox 5.0 Mustang Tech
Replies
11
Views
421
Fox 5.0 Mustang Tech Oct 11, 2026
limp
Engine 87 NA - Tune or no Tune needed?
  • R82148V
  • Sep 17, 2025
  • Fox 5.0 Mustang Tech
Replies
8
Views
511
Fox 5.0 Mustang Tech Sep 17, 2025
R82148V
A
Catch can questions.
  • AngryH58
  • Sep 26, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
171
1996 - 2004 SN95 Mustang -General/Talk- Sep 29, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?