• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

OPINIONS/ADVICE NEEDED

  • Thread starter Thread starter blckstng96
  • Start date Start date Feb 12, 2008

blckstng96

Member
Apr 13, 2004
208
0
16
Feb 12, 2008
#1
  • Feb 12, 2008
  • #1
im haveing a problem with my 88lx.it doesnt like to start on its own and once you get it started it runs horrible.the car will only start on starting fluid and once its running it will idel but very rough and surge a lot.also when you go to drive it it stumbles like crazy and has no power,like its missing and starving for fuel backfiring out the intake.i put a new regulator in it and replaced the map sensor.niether of those seem to help.we had adjusted the timing to because it was all out of wack.so right now im thinking fuel pump but not sure.the fuel pump works because i can hear it but not sure if its working how it should and i dont have access to a gauge to put on it while driving to see what pressure is at under load.i bought the car off a guy not running so im not sure on history of things but i do know he said the pump was replaced thinkin it was that and whoever had replaced it ran the wiring incorrect and the pump goes on and stays on as soon as the ignition is engaged instead of the 20sec or so prime then stop until start.any input greatly appreciated.i just need to get this thing running without dumping a ton of money into it.thanks guys
 

ttop88

Member
Mar 12, 2007
42
0
6
indiana
Feb 12, 2008
#2
  • Feb 12, 2008
  • #2
You don't need to see pressure under load. Check it at idle. Sounds like its low. Will it prime? You should be able to tell by sound. Parts store pumps are junk,and it sounds like thats what you have.
 

blckstng96

Member
Apr 13, 2004
208
0
16
Feb 12, 2008
#3
  • Feb 12, 2008
  • #3
yeah i can hear it prime,it actually stays on as soon as ignition is turned over to acc position.someone must have rewired it.i know it works as far as powering on and stuff but as far as working correctly and having correct presure,thats another story.but its odd because its smells rich but runs like its leans and not getting enough fuel.so im thinking the pressure is low and instead of the normal injector spray pattern its just pretty much dripping and putting out the flame
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 12, 2008
#4
  • Feb 12, 2008
  • #4
Dump the codes and see what the computer says is wrong…Codes may be present in the computer even if the Check Engine light isn’t on.

Here's the link to dump the computer codes with only a jumper wire or paper clip and the check engine light, or test light or voltmeter. I’ve used it for years, and it works great. You watch the flashing test lamp or Check Engine Light and count the flashes.

See http://www.troublecodes.net/Ford/





IF your car is an 86-88 stang, you'll have to use the test lamp or voltmeter method. There is no functional check engine light on the 86-88's except possibly the Cali Mass Air cars.



89 through 95 cars have a working Check Engine light. Watch it instead of a test lamp.



Codes have different answers if the engine is running from the answers that it has when the engine isn't running. It helps a lot to know if you had the engine running when you ran the test.

Trouble codes are either 2 digit or 3 digit, there are no cars that use both 2 digit codes and 3 digit codes.

For those who are intimidated by all the wires & connections, see http://www.actron.com/product_detail.php?pid=16153 for what a typical hand scanner looks like. Normal retail price is about $30 or so at AutoZone or Wal-Mart.

Or for a nicer scanner see http://www.midwayautosupply.com/pc-7208-90-equus-digital-ford-code-reader-3145.aspx – It has a 3 digit LCD display so that you don’t have to count flashes or beeps.. Cost is $30.
 

blckstng96

Member
Apr 13, 2004
208
0
16
Feb 12, 2008
#5
  • Feb 12, 2008
  • #5
a friend of mine has a little scanner tool so i'll connect that up to it and see what we got
 
You must log in or register to reply here.

Similar threads

S
92 5.0 almost starts
  • Steverino
  • Sep 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
5
Views
276
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 25, 2026
General karthief
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
520
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
J
i need help
  • JK.
  • Oct 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
22
Views
611
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 28, 2026
JD1964
Fox Fuel Pump Issues After Replacement/Upgrade
  • Ryu
  • Jun 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
24
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 13, 2026
Ryu
I
1994 Cobra - Fuel Pressure Drops Revving at Idle
  • IconicSilverGT500
  • Apr 11, 2026
  • 1994 - 1995 Specific Tech
Replies
16
Views
687
1994 - 1995 Specific Tech Apr 24, 2026
Mcmahst
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?