Please kill me

BACKINTANG · Sep 20, 2005

I can't take the pain anymore. Please sneak into my house while I am asleep, look in my nightstand drawer, pull out the .45 and shoot me. Or you can just bring a trailer and take this %$^*$#@^*!#@$)!&@ Mustang out of the garage. Ok enough of that. I finally removed the master cylinder by removing it via under the dash. I got the pushrod out with the piston attatched. How do you get the piston off of the push rod. Do I beed to buy a new pushrod for my new duel MC? I just bought a new M1A (rifle) and I am at the point that I want to use the car as a target. Damn I need a valium or a new hobby.

hungrymonkey · Sep 20, 2005

your pushrod stuck in the master cylinder?
i take it you have manual brakes.

When In doubt, use a hammer.
If that does not work, then light it on fire.

geordie · Sep 20, 2005

Ha......do I sense a little frustration there?

How much does the job pay and do you cover expenses?

Seriously though......needlework is fun and if you make a balls of it, you can pull the stitches out and start again.

12sec67 · Sep 20, 2005

the pushrod is held inside the master cyl with a type of clip. put the MC on a vise and use some leverage to pull it out.

the best part about doing something you never done is figuring out a way to not let it beat you.

IF IT WAS EASY EVERYONE WOULD TRY TO RESTORE AN OLD CAR.

67coupestang · Sep 20, 2005

ususally when ive gotten a new m/c its come with the pushrod, other wise mount it in a vise and use a slide hammer on it and whack the crap out of it. its held in with a clip

BACKINTANG · Sep 21, 2005

I have consumed 2 very good beers (Carolina beer company Frostbite) and feel much better. I did get the snap ring out. Tommorrow I will put it in the vise and hit it with a slide hammer. For now I will consume some more and go sit in the hot tub and contemplate buying a totally restored 66 fastback. Yes I do have manual brakes. The only reason I am restoring this car is because it was the car I learned to drive in. My father purchased it new in 66. He hit his second childhood in 85 and purchased a new 85 GT. The car sat for 11 years under an oak tree before I gained possesion in 96. I finally have the time and money to get it together. I know I could pay for someone else to do the job, but I want to have bragging rights that I did it myself. I am now paying for the 11 years it sat unattended. Oh well, it beats sitting in a bar.

12sec67 · Sep 21, 2005

i'm all for drinking beer when working on my car except for some strang reason not drinking when i do the brakes

besides that ...

Hack · Sep 21, 2005

BACKINTANG said:
I can't take the pain anymore. Please sneak into my house while I am asleep, look in my nightstand drawer, pull out the .45 and shoot me. Or you can just bring a trailer and take this %$^*$#@^*!#@$)!&@ Mustang out of the garage. Ok enough of that. I finally removed the master cylinder by removing it via under the dash. I got the pushrod out with the piston attatched. How do you get the piston off of the push rod. Do I beed to buy a new pushrod for my new duel MC? I just bought a new M1A (rifle) and I am at the point that I want to use the car as a target. Damn I need a valium or a new hobby.

One thing you will notice as you spend more time working on your car is that it gets much easier. There are a lot of little tricks in how to do various things, and just knowing what size wrench to grab by looking at the fastener saves a lot of time.

I've also noticed that when I have a deadline a project can become less fun. I'm currently working on swapping a 302 into my car, and I'm worried about beating the snow. Being in a hurry puts a damper on things and tempts you to cut corners. The results can suffer.

Anyway, good luck and I hope things go better.

2nd Mustang · Sep 21, 2005

I'm in my second childhood. I finally got that 67 coupe that I always wanted. As my lady friend says, it's cheaper than a head shrink.

LMan · Sep 21, 2005

I think your original emotions were correct - that car is too much trouble, you should not waste any more time on it.

I will PM my address later, will be happy to take that abortion off your hands and contribute thusly to your longer, better life

19stang66 · Sep 21, 2005

The directions that came with my SSBC disc conversion kit say to put the cylinder thing the pushrod is in, in a vise and use a hacksaw to cut it parallel with the pushrod half way through. Don't cut it too far or you'll just end up cutting the pushrod itself. Another way I found out is to put the pushrod and the thing surrounding the end of it in the vise grip and keep tightening the vise grip until it cracks off. It's not that strong of metal. Maybe it worked because I already started to cut it in half. I can't look at the directions right now because i'm at school. Yay for study hall

65ShelbyClone · Sep 22, 2005

Maybe its different for a '68, but the pushrod for my MC just slides out. It had an o-ring, but nothing for a clip to catch on.

hungrymonkey · Sep 22, 2005

mine to.

65fastback2+2 · Sep 22, 2005

hungrymonkey said:
your pushrod stuck in the master cylinder?
i take it you have manual brakes.

When In doubt, use a hammer.
If that does not work, then light it on fire.

i thought you ran whatever over first, then lit it on fire

302 coupe · Sep 22, 2005

no snap ring or clip holding my pushrod in place either. When I unbolt the master cylinder, the pushrod stays behind

Edbert · Sep 22, 2005

Hack said:
I'm currently working on swapping a 302 into my car, and I'm worried about beating the snow.

I can completely understand, I have been waiting for 4 long months for the temperatures in my garage to dip down to the 90s, so I can get some more work done. I cannot stand working while sweat drips into my eyes and onto the project.

krash kendall · Sep 22, 2005

BACKINTANG said:
I finally removed the master cylinder by removing it via under the dash.

How or why did you do that? The M/C is nutted onto two studs through the firewall in the engine bay coming from the brake bracket

yeloxr7 · Sep 22, 2005

Go Back and Read His Posts.......

krash kendall said:
How or why did you do that? The M/C is nutted onto two studs through the firewall in the engine bay coming from the brake bracket

Remember he said he has manual brakes, so the master cylinder is bolted directly to the firewall, and the nuts that hold it in place are accessible inside the car. Kinda like removing the booster/master cylinder from a power-brake car.

302 coupe · Sep 22, 2005

uh...the bolts that you remove are under the hood. No need to get under the dash to unbolt it. The nuts are held in place with some little square brackets, so you can't get a wrench on them anyway (at least thats the way my original 66 coupe is).

65ShelbyClone · Sep 22, 2005

Yeah, the pedal support has permanent threaded inserts, not removable nuts. The MC bolts thread in from the engine bay.

EDIT: Unless someone stripped out the inserts and had to use longer bolts with nuts on the back.

Please kill me

BACKINTANG

New Member

hungrymonkey

White by Birth, Trash By Choice

geordie

12sec67

Active Member

67coupestang

BACKINTANG

New Member

12sec67

Active Member

Hack

2nd Mustang

LMan

19stang66

Member

65ShelbyClone

hungrymonkey

White by Birth, Trash By Choice

65fastback2+2

New Member

302 coupe

Edbert

krash kendall

Active Member

yeloxr7

Member

302 coupe

65ShelbyClone

Similar threads

Please kill me

New Member

White by Birth, Trash By Choice

Active Member

New Member

Active Member

Member

White by Birth, Trash By Choice

New Member

Active Member

Member

Similar threads

Privacy & Transparency

Privacy & Transparency