• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Power steering pump leaking....

  • Thread starter Thread starter BYRDPE
  • Start date Start date Feb 28, 2008
B

BYRDPE

Founding Member
Nov 4, 1998
1,556
0
37
Memphis,Tn.
Feb 28, 2008
#1
  • Feb 28, 2008
  • #1
Can't really tell where it's leaking from. Doesn't look like it coming from the hoses.
Where are they prone to leak from?
Also what involved in replacing one?
Thanks
 

cenok is family

15 Year Member
Jun 25, 2003
1,409
69
79
Norman, Ok
Feb 28, 2008
#2
  • Feb 28, 2008
  • #2
they're PRONE to leaking from the pressure line. lol. usually the o-ring goes out. also, over time the return line will start to crack and that can be the culprit. other than that, if too much pressure builds up they can overflow a bit from the cap. as far as what's involved in replacing one, you have to remove the a/c compressor and bracket, fan and shroud. you'll have to use your old pulley and bracket so you'll need a power steering pulley puller to get both the pulleyand bracket off your old pump.
 
B

BYRDPE

Founding Member
Nov 4, 1998
1,556
0
37
Memphis,Tn.
Feb 28, 2008
#3
  • Feb 28, 2008
  • #3
Thanks for the reply.
Which line is the high pressure line?
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 29, 2008
#4
  • Feb 29, 2008
  • #4
The return hoses are all low pressure and are most commonly secured to the pump and associated plumbing with worm gear hose clamps. After a while they will frequently soften up at the end where they are clamped, and should be replaced. The auto parts store will sell you hose by the foot and it takes about 3 feet or less, depending if you have the fluid cooler in the low pressure side of the line.

Each hose uses an O ring on each end to seal them. The hoses will swivel when they are installed and tightened into place. That is why there are O rings on the fittings. The O ring is the part that actually makes the pressure seal. If you slide the nut all the way back as far as it will go, you will see the O ring and the groove cut into the center section of the fitting.


Sometimes you will get some white Teflon rings with the pump or rack. The rings go on the threaded part of the fitting to reduce or prevent small leaks. They are not meant to seal the pressure part of the line or substitute for the rubber O ring. Heat the white Teflon seals in hot water and they will be easier to install. You can install the fittings without them and not have any leaks if the O rings seal good.

You may find it is easier to drop the rack down to get to the hose fittings. The flex coupling for the steering shaft needs to be disconnected before you can get the rack out. You should disassemble the coupling by undoing the 2 bolts that hold it together.

Remove the two bolts that bolt the rack assembly to the frame and then pull the rack down. Get a catch pan to dump the fluid in when you disconnect the hydraulic lines. I replaced the rack mount bushings with some Energy Suspension urethane ones. When you re-install the rack assembly, put the rear bushings in the rack assembly and lift it into place. Then install the front bushings & washers and tighten down the nuts. Doing it this way makes room for the hydraulic lines without having them bind against the frame.
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Feb 29, 2008
#5
  • Feb 29, 2008
  • #5
They will also leak where the high pressure fitting goes into the tank. There are 2 O rings on that fitting and they are super easy to change. Just remove the fitting, remove the old O rings, clean it up, put the new O rings on it and reinstall it. Torque it to 30 ft lbs.

I just replaced all of the seals in my pump. They're not that hard to do. You can also get a chance to see if anything needs replacing inside of the pump.
 
B

BYRDPE

Founding Member
Nov 4, 1998
1,556
0
37
Memphis,Tn.
Feb 29, 2008
#6
  • Feb 29, 2008
  • #6
Thanks guys.
I'll be trying the leaking hose first.
It's not coming from the rack. It also looks like it could be coming from behind the pulley.
Are there any seals in this area?
 

Maryland Stang

Active Member
Aug 21, 2002
1,656
30
39
Greenville, NC
Mar 1, 2008
#7
  • Mar 1, 2008
  • #7
BYRDPE said:
Thanks guys.
I'll be trying the leaking hose first.
It's not coming from the rack. It also looks like it could be coming from behind the pulley.
Are there any seals in this area?
Click to expand...

Yes, there is a shaft seal. With care it could be removed without disassembling the pump. Just try not to nick up the shaft when removing the old one. There is a metal seal retainer that's pops right off and then the seal.
 
You must log in or register to reply here.

Similar threads

S
1965 Mustang with 80s 5.0 engine in it Power Steering hose or connection ID?
  • spearce
  • May 19, 2026
  • Classic Mustang Specific Tech
Replies
2
Views
235
Classic Mustang Specific Tech Jun 8, 2026
AeroCoupe
K
86 GT Water Pump
  • Kade5114
  • May 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
228
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 11, 2026
nickyb
P
Engine Mysterious coolant leak at back of engine
  • palerider94
  • Jan 18, 2026
  • Fox 5.0 Mustang Tech
Replies
1
Views
281
Fox 5.0 Mustang Tech Jan 19, 2026
AeroCoupe
A
Resolved 302 oil leak when running
  • AlexM556
  • Sep 8, 2026
  • Classic Mustang Specific Tech
  • 2
Replies
36
Views
1K
Classic Mustang Specific Tech Nov 1, 2026
manicmechanic007
D
Loud noise(s) from Engine Bay
  • DuluthFoxbody
  • Oct 25, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
14
Views
375
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 5, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?