• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Proper way to install Harmonic Damper

  • Thread starter Thread starter juiced_94gt
  • Start date Start date Jun 12, 2007

juiced_94gt

Active Member
Mar 30, 2005
1,143
0
36
Southern California
Jun 12, 2007
#1
  • Jun 12, 2007
  • #1
Whats the proper way?? just hit it with the impact gun??? that's how repair shops do it or is there a better way?
 

go-stang5.0

New Member
Jan 27, 2003
2,244
0
0
Glenview,Il
Jun 12, 2007
#2
  • Jun 12, 2007
  • #2
If you can hold the motor in place you don't need an impact. You can also try a breaker bar w/ extension (such as pipe) under the pass. side fender against the ground. and cranking over the motor.
 

juiced_94gt

Active Member
Mar 30, 2005
1,143
0
36
Southern California
Jun 12, 2007
#3
  • Jun 12, 2007
  • #3
Im trying to install it while the motor is on the engine stand.
 

95strokerPSU

Member
Jul 29, 2004
986
1
19
Sacramento from Philly
Jun 12, 2007
#4
  • Jun 12, 2007
  • #4
From what I remember, I just lined up the keyway (I think that's what the groove is called) and pushed it on by hand a little. Then used the damper bolt to move it all the way on.
 

Stanger007

Founding Member
Sep 26, 2001
2,015
2
46
Baton Rouge, LA
Jun 12, 2007
#5
  • Jun 12, 2007
  • #5
You can rent an installer tool or just hit it with an impact. I hit the balancer with my impact on my '72 302 while it was on the stand.

Wes
 

The Green GT

No 13 year olds are safe around me.
10 Year Member
Jan 8, 2006
1,269
19
99
Louisiana
Jun 12, 2007
#6
  • Jun 12, 2007
  • #6
95strokerPSU said:
From what I remember, I just lined up the keyway (I think that's what the groove is called) and pushed it on by hand a little. Then used the damper bolt to move it all the way on.
Click to expand...

Same here.
 

Grn92LX

Fidanza Man!
Founding Member
Jan 14, 2001
6,819
64
129
New York
Jun 12, 2007
#7
  • Jun 12, 2007
  • #7
The proper way is to use a tool then hit it with a torque wrench.
 
R

red95gtconvert

New Member
May 29, 2006
382
0
0
Ponca city, OK
Jun 12, 2007
#8
  • Jun 12, 2007
  • #8
The last 2 times I did it I just put antiseize on the crankshaft snout, slid the balancer on, put loctite on the balancer bolt, zipped it on with my impact and called it a day.
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Jun 12, 2007
#9
  • Jun 12, 2007
  • #9
Many have opinions on the right and wrong way to do it.

I have found that just installing it with a bolt works very easy and mimics the 'tool' that could be used.

Just put the balancer on by hand (keyway lined up) and then just thread the bolt in and bolt it on. Torquing to 90-100 ft lbs will do.

Be careful with an impact. Impacts have different power so how do you know how much torque is being applied at a particular moment. Unless you like risking stripping out the crank or breaking a bolt.

Ratchet wrench/Torque wrench is a bit better at this.

You can use an impact, just not what I have used. I have seen the 'cons' of using an impact.
 
You must log in or register to reply here.

Similar threads

Flushing water from the radiator and block.
  • djj62478
  • Oct 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
259
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 11, 2026
CAMTWO1070
B
water pump installation questions
  • B0udreaux
  • Feb 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
38
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 28, 2026
General karthief
Engine Keeping O2 sensors lit with long tube headers
  • keel
  • Jul 30, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
282
Fox 5.0 Mustang Tech Aug 21, 2026
Qtrhrse23
Salvage/rebuilt title question
  • djj62478
  • Oct 2, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
213
1996 - 2004 SN95 Mustang -General/Talk- Oct 2, 2026
DadLife0724
Most ridiculous / dishonest work you have heard a shop recommend?
  • SchwarzStock
  • Jul 19, 2026
  • Off-Topic Hangout
Replies
4
Views
145
Off-Topic Hangout Jul 20, 2026
SchwarzStock
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?