• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Pulled some codes

  • Thread starter Thread starter ColdAudio
  • Start date Start date Jan 17, 2006
C

ColdAudio

New Member
Jan 9, 2006
31
0
0
Jan 17, 2006
#1
  • Jan 17, 2006
  • #1
And here are the results!

12
21
24
26
34
85

KEOE testing, car wouldnt run w/ scanner plugged in
Any help?
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Jan 17, 2006
#2
  • Jan 17, 2006
  • #2
year model? more info. does it run? idle rough ect... click on link for computer code definitions.

http://www.muscularmustangs.com/test2.php

also click on this link you might want to perform steps 1-5 in solving idle problems and reset computer and drive and repull codes might eliminate a few.

http://www.muscularmustangs.com/maintain.php
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 17, 2006
#3
  • Jan 17, 2006
  • #3
Code 12 -Idle Air Bypass motor not controlling idle properly (generally idle too low) - IAB dirty or not working. Take it off and clean it thoroughly with throttle body cleaner. Clean the electrical contacts with non flammable brake parts cleaner at the same time.

Code 21 – ECT sensor out of range. Broken or damaged wiring, bad ECT sensor. Note that that if the outside air temp is below 50 degrees F that the test for the ECT can be in error.

The ECT sensor has absolutely nothing to do with the temperature gauge. They are different animals. The ECT sensor is normally located it the RH front of the engine in the water feed tubes for the heater.

The ACT & ECT have the same thermistor, so the table values are the same

ACT & ECT test data:

Use Pin 46 on the computer for ground for both ECT & ACT to get most accurate readings.

Pin 7 on the computer - ECT signal in. at 176 degrees F it should be .80 volts

Pin 25 on the computer - ACT signal in. at 50 degrees F it should be 3.5 volts. It is a good number if the ACT is mounted in the inlet airbox. If it is mounted in the lower intake manifold, the voltage readings will be lower because of the heat transfer.

Voltages may be measured across the ECT/ACT by probing the connector from the rear. Use care in doing it so that you don't damage the wiring or connector.

Here's the table :

68 degrees F = 3.02 v
86 degrees F = 2.62 v
104 degrees F = 2.16 v
122 degrees F = 1.72 v
140 degrees F = 1.35 v
158 degrees F = 1.04 v
176 degrees F = .80 v
194 degrees F = .61

Note that all resistance tests must be done with power off. Measuring resistance with a circuit powered on will give false readings and possibly damage the meter.

Ohms measures at the computer with the computer disconnected, or at the sensor with the sensor disconnected.
50 degrees F = 58.75 K ohms
68 degrees F = 37.30 K ohms
86 degrees F = 27.27 K ohms
104 degrees F = 16.15 K ohms
122 degrees F = 10.97 K ohms
140 degrees F = 7.60 K ohms
158 degrees F = 5.37 K ohms
176 degrees F = 3.84 K ohms
194 degrees F = 2.80 K ohms

Code 24 - Intake Air Temperature (ACT) sensor out of range. Bad sensor, bad wiring. The ACT for Mustangs built before 95 is in the #5 intake runner. It measures the air temperature in the intake to help computer the proper air/fuel ratio.

Note that that if the outside air temp is below 50 degrees F that the test for the ACT can be in error.

ACT & ECT test data:

The ACT & ECT have the same thermistor, so the table values are the same

Pin 7 on the computer - ECT signal in. at 176 degrees F it should be .80 volts

Pin 25 on the computer - ACT signal in. at 50 degrees F it should be 3.5 volts. It is a good number if the ACT is mounted in the inlet airbox. If it is mounted in the lower intake manifold, the voltage readings will be lower because of the heat transfer. Here's the table :

68 degrees F = 3.02 v
86 degrees F = 2.62 v
104 degrees F = 2.16 v
122 degrees F = 1.72 v
140 degrees F = 1.35 v
158 degrees F = 1.04 v
176 degrees F = .80 v
194 degrees F = .61

Note that all resistance tests must be done with power off. Measuring resistance with a circuit powered on will give false readings and possibly damage the meter.

Ohms measures at the computer with the computer disconnected, or at the sensor with the sensor disconnected.
50 degrees F = 58.75 K ohms
68 degrees F = 37.30 K ohms
86 degrees F = 27.27 K ohms
104 degrees F = 16.15 K ohms
122 degrees F = 10.97 K ohms
140 degrees F = 7.60 K ohms
158 degrees F = 5.37 K ohms
176 degrees F = 3.84 K ohms
194 degrees F = 2.80 K ohms

Code 26 Mass Air Flow (MAF) out of range. Bad MAF sensor, MAF wiring shorted to 12 volt power, MAF ground fault.

Code 34 Or 334 - EGR voltage above closed limit - Failed sensor, carbon between EGR pintle valve and seat holding the valve off its seat. Remove the EGR valve and clean it with carbon remover. Prior to re-installing see if you can blow air through the flange side of the EGR by mouth. If it leaks, there is carbon stuck on the pintle valve seat, replace the EGR valve ($85-$95).

If the blow by test passes, and you have replaced the sensor, then you have electrical ground problems. Check the resistance between the black/white wire on the MAP/BARO sensor and then the black/white wire on the EGR and the same wire on the TPS. It should be less than 1 ohm. Next check the resistance between the black/white wire and the negative battery post. It should be less than 1 ohm.

Note that all resistance tests must be done with power off. Measuring resistance with a circuit powered on will give false readings and possibly damage the meter.

Let’s put on our Inspector Gadget propeller head beanies and think about how this works:
The EGR sensor is a variable resistor with ground on one leg and Vref (5 volts) on the other. Its’ resistance ranges from 4000 to 5500 Ohms measured between Vref & ground, depending on the sensor. The center connection of the variable resistor is the slider that moves in response to the amount of vacuum applied. The slider has some minimum value of resistance greater than 100 ohms so that the computer always sees a voltage present at its’ input. If the value was 0 ohms, there would be no voltage output. Then the computer would not be able to distinguish between a properly functioning sensor and one that had a broken wire or bad connection. The EGR I have in hand reads 700 Ohms between the slider (EPV) and ground (SIG RTN) at rest with no vacuum applied. The EGR valve or sensor may cause the voltage to be above closed limits due to the manufacturing tolerances that cause the EGR sensor to rest at a higher position than it should.

This will affect idle quality by diluting the intake air charge

Code 85 - CANP solenoid - The Carbon Canister solenoid is inoperative. Check vacuum lines for leaks and cracks. Check electrical wiring for loose connections, damaged wiring and insulation. Check solenoid valve operation by grounding the gray/yellow wire to the solenoid and blowing through it.
The computer provides the ground for the solenoid. The red wire to the solenoid is always energized any time the ignition switch is in the run position.
 
C

ColdAudio

New Member
Jan 9, 2006
31
0
0
Jan 17, 2006
#4
  • Jan 17, 2006
  • #4
Doh can't believe I forgot the basic info! 1989 GT, runs and drives fine seems a little sluggish at times, I pulled the codes because on the random occassion the CEL will come on and the car will backfire/sputter and just run terrible.

Thank you for the awesome replies, it is alot lower than 50 degrees here so those sensors may not be bad, it should be warmer this weekend I'll test them then.

I swapped in a new MAS and made sure the plug was clean/connected well, so I really need to clear the codes and test again after I fix a few other things.

The Carbon canister, is this an emissions thing related in any way to the smog pump? When I bought the car, the previous owner removed many emissions things from the car, is it possible something is unplugged/missing?

When I started the car with the code reader plugged in, the car would struggle then die out. Any idea why? No running CEL before or afterwards, but I couldn't even check anyway.

Thanks again for the replies, luckily it doesn't seem to have any major issues just a few sensors and whatnot, maybe I'll have an easy weekend
 
You must log in or register to reply here.

Similar threads

M
Electrical 93 5.0 No Injector Pulse
  • machinermac
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
15
Views
518
Fox 5.0 Mustang Tech Aug 1, 2026
Willybill32
2
Running very very rich
  • 2esoteric
  • Oct 31, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
469
Fox 5.0 Mustang Tech Oct 31, 2025
Noobz347
Forced Induction Total Timing under boost
  • Dontknowchit
  • Aug 27, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
429
Fox 5.0 Mustang Tech Aug 28, 2025
Dontknowchit
B
Engine 14k mile 1993 5.0 long crank
  • bullet3964
  • Jul 26, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
228
Fox 5.0 Mustang Tech Jul 26, 2025
AeroCoupe
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
317
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?