Pulling motor!!!! HELP

Is this the week to pull motors or what. I'm just about ready to lift my motor out.
SV400009.JPG
[/IMG]
This is what's going in it's place.
 
RacEoHolic330 said:
I also reccommend putting different bolts in small snack bags and labeling them. That will really come in handy when you have 2 dozen bolts laying around that need to go somewhere.


Indeed, I put them in seperate trays with a post-it note.

Turns out I'm gonna need an easy out, and something else to get these facking header bolts off. Easy out is for the bolt that broke from the upper maninfold into the lower.

Manifold is off, driver's side injectors are disconnected, and I'm gonna get the other side and fuel rails off tomorrow. I'm hoping to have it sitting in a tire by Wednesday.
 
bynummustang said:
Indeed, I put them in seperate trays with a post-it note.

Turns out I'm gonna need an easy out, and something else to get these facking header bolts off. Easy out is for the bolt that broke from the upper maninfold into the lower.

Manifold is off, driver's side injectors are disconnected, and I'm gonna get the other side and fuel rails off tomorrow. I'm hoping to have it sitting in a tire by Wednesday.

Are you keeping the stock h-pipe and header? If not, cut them, take 5 seconds and then you can deal with getting the header off when its out. This will save you time and get the 347 in.
 
bynummustang said:
I'm undecided on x pipe. I want long tubes, but then I'll need new x-pipe also, but I'd like to save the pipe atleast, maybe sell it to make a little profit.
Been here, and good luck selling it for nothing. No one wants a H-pipe with cats, especially a stock one. Plus it will cost more than an arm/leg to ship it. I would junk it. Besides, you won't be able to mount long tubes on a stock pipe.

Jason
 
Killer50stang said:
Been here, and good luck selling it for nothing. No one wants a H-pipe with cats, especially a stock one. Plus it will cost more than an arm/leg to ship it. I would junk it. Besides, you won't be able to mount long tubes on a stock pipe.

Jason


My currenct x-pipe is a BBK 2.5 catted pipe. High flow cats. The headers are MAC somethings, but I never really liked them. There are a few people with stock 5.0's in my area who are getting the mod bug.
 
bynummustang said:
My currenct x-pipe is a BBK 2.5 catted pipe. High flow cats. The headers are MAC somethings, but I never really liked them. There are a few people with stock 5.0's in my area who are getting the mod bug.

Mod bug? I hope this isn't a stock 5.0 with a CHIP and a C.O.I. Stay away from these guys who think their car is fast and runs 10's. Dump the cats, you don't want them, plus your car will sound way better. MAC makes a pretty crappy header in my opinion, same with the X-pipe. I had some and they were generic. You can always tell the difference between MAC and BBK or Bassani. The welds on the Macs suck or at least they used to. MAC is cheaper, but you get what you pay for.
 
UPDATE

Well, I went back out, and finally got some time to work on it.

Still have the fawking header bolts (1 per side), PS Pump and drive shaft to get off. Everything else is ready.

To all who say that they can get the shifter out in 20 minutes I call :bs:. I took my time, but wasn't doin one screw ever 20 minutes. It took me a LONG time just to get the plastics out of the way. But I did get my find out that my shifter is a Hurst and not a 50 shifter as I was told.

Picture063.webp


Picture064.webp


Daggar and timeless, I'm sorry for the bird, but at picture time I was not happy with the shifter, so I was glad when I got down to the last 4 bolts.






I've grown to like this view of my car.

Picture052.webp






And lastly a pictuer of most of the wires, and harnesses out of the way. And PB Blaster, I'll take my endorsement*sp money to [email protected] through paypal.
Picture060.webp
 

Attachments

  • Picture063.webp
    Picture063.webp
    74.3 KB · Views: 119
  • Picture064.webp
    Picture064.webp
    98.8 KB · Views: 117
  • Picture052.webp
    Picture052.webp
    34.5 KB · Views: 112
  • Picture060.webp
    Picture060.webp
    45.2 KB · Views: 124
Wow, crap, I didn't realize how big those pics were. Sorry.

On a different note, how to you guys recomend getting the 4 12mm bolts off the DS at the rear end? I tried with it in gear, and that didn't help.The shaft or tires depending if it was in gear kept turning. Do you have to use an impact gun? or should I bathe them in PB then try again with the 3/8" rachet and universal flex joint?
 
bynummustang said:
Wow, crap, I didn't realize how big those pics were. Sorry.

On a different note, how to you guys recomend getting the 4 12mm bolts off the DS at the rear end? I tried with it in gear, and that didn't help.The shaft or tires depending if it was in gear kept turning. Do you have to use an impact gun? or should I bathe them in PB then try again with the 3/8" rachet and universal flex joint?


car in gear, emergency brake up. i usually use my feet for leverage. make sure u loctite them back up when installing them