Pypes Muffler Delete system hanging on one side, help

dmaxstang

New Member

Jul 29, 2005

0

0

0

dallas

Sep 3, 2008

#1

• Sep 3, 2008

• #1

I just put on the PYPES muffler delete system on my 05 GT, (by the way, sounds amazing), but the passenger pipe hangs about 1/2 inch to 3/4 inch low and i can't seem to get it adjusted to a good place, any suggestions? I know i have seen this somewhere before on the board, but i can't find it with a search. Thanks a ton, because that is all it needs to be absolutely perfect. A pic will follow soon after.

 

bigcat

start with the upper hole, and if more traction is

May 1, 2005

3,015

1

79

7200 feet

Sep 3, 2008

#2

• Sep 3, 2008

• #2

try rotating the over the axle pipe. check the ultimate sticky too, probably listed in there somewhere. there is so much info there, i forget what all is there!

 

dc06gt

New Member

Apr 8, 2008

24

0

0

Jersey

Sep 3, 2008

#3

• Sep 3, 2008

• #3

I have them on my car and the drivers one went right where I wanted to and the passenger one was way down and off to the passenger side. I ended up carefully bending the hanger that's welded on the pipe to get it to sit properly. yours doesn't sound as extreme.

 

dmaxstang

New Member

Jul 29, 2005

0

0

0

dallas

Sep 3, 2008

#4

• Sep 3, 2008

• #4

DC, did you have problems getting that passenger side to go over the pipe also? I must have worked on that side for nearly and hour and a half, then that side is hanging. I will more than likely try bending the hanger and cutting off a little bit. Thanks

 

dc06gt

New Member

Apr 8, 2008

24

0

0

Jersey

Sep 3, 2008

#5

• Sep 3, 2008

• #5

I had no problems with the pipes themselves just that one hanger seemed to long or welded in the wrong place.

 

sonnier

Member

Jan 7, 2008

56

0

6

Pearland, TX

Sep 12, 2008

#6

• Sep 12, 2008

• #6

I cut mine and re-welded it on for proper fitment, but that is kind of the hard way.

 

dc06gt

New Member

Apr 8, 2008

24

0

0

Jersey

Sep 12, 2008

#7

• Sep 12, 2008

• #7

I was thinking about doing that but I got to lazy to go get my welder.

 

P

pile_53574

Member

May 1, 2005

30

4

19

SW WI

Sep 21, 2008

#8

• Sep 21, 2008

• #8

I have delete pypes also, the only prob/issue i'm having is vibration/noise when the car is under load, not there all the time but it drives the wife crazy. I've tightened the clamps many times and even snapped on of the bolts in the clamp, only solution I can figure is to weld them together instead of clamps?? But yeah LOVE the sound!!

 

D

dro

New Member

May 25, 2003

165

0

0

Birmingham, AL

Sep 21, 2008

#9

• Sep 21, 2008

• #9

Yep, adjust the over the axle pipe on the Hpipe to catback. Fixes it right up. Just did it today actually...

 

NastyStang113

New Member

Sep 12, 2008

1,567

1

0

Florida

Sep 21, 2008

#10

• Sep 21, 2008

• #10

dro said:

Yep, adjust the over the axle pipe on the Hpipe to catback. Fixes it right up. Just did it today actually...

Click to expand...

Bingo, you beat me to it !!