• Mustang Forums
  • 2005 - 2014 S-197 Mustang -General/Talk-
  • 2005 - 2009 Specific Tech

Question for those that dyno'd

  • Thread starter Thread starter sacrstang
  • Start date Start date Sep 20, 2006

sacrstang

New Member
Mar 30, 2005
76
0
0
Sep 20, 2006
#1
  • Sep 20, 2006
  • #1
When you put your S197 on the dyno did you have all your exhaust components on or did you leave the headers wide open by taking the exhaust system off?
The reason I ask is because I got to talkin to an old schooler. He used to run his 68 or 69 mustang at the track. He gave me a couple tips. If I took the car out again he said that I should try running without my exhaust system on and the headers wide open (which I will have to check and see if it is ok at my local track) and he said he would fabricate a device for me called a torque sling. It prevents the engine from moving side to side and forces all the power back instead of sideways when mashing the gas. He also asked if I knew what kind of horse power and torque my car puts out and I don't know because I have not been to the dyno yet. But I have seen some numbers in magazines and on here of course and they are around the 270-295 hp range. He insisted with the tips that he gave me and the mods I already have done the car should be close to the mid 300's at wide open throttle. I'm open to trying these as the sling is removable and the exhaust system can be put back on.
 
W

warlock1313

New Member
May 21, 2005
5
0
0
Sep 21, 2006
#2
  • Sep 21, 2006
  • #2
My 06 gt put down 296hp and 310 lbft toruqe with an x-pipe c&l, tune, 410's. I pulled the factory mufflers and lost 3hp and 5lbft torque. I dont see any power gain from unbolting the exhaust from the manifolds. For a stock system (headers and mufflers) it flows very well. As far as what the other guy did with his old school ride.... its a different animal.

Besides I wanted real world numbers, not some rigged track only readings.
 

StonePony

New Member
Jan 10, 2006
218
0
0
Sep 21, 2006
#3
  • Sep 21, 2006
  • #3
If your car was highly modded the open headers might gain you a few horses. However with your mods I think the lack of back-pressure will hurt.
Remember the GTs in 2005 -2007 have 2.5" mandrel bent exhaust. It is not like the old bent-up skinny exhaust Ford used in the 60's on Mustangs.
The torque sling is just a chain that is bolted to your head/block to the frame and anchors the engine from lateral twist. you can accomplish the same thing and no noticable chains by changing your motor mounts to solid or urethane.
The car may shake a little more.
I am an old timer and I ran open headers at the track before but only in a highly modified engine. Natrually aspirated engines like some back-pressure. Forced induction can benefit from more open exhaust.
 

5ive.oh

Founding Member
Feb 23, 2001
195
0
0
Rocky Mountain House, AB
Sep 21, 2006
#4
  • Sep 21, 2006
  • #4
Removing the air filter will net you 15-20 hp too. j/k
 

sacrstang

New Member
Mar 30, 2005
76
0
0
Sep 21, 2006
#5
  • Sep 21, 2006
  • #5
Thanks for the answers guys. The guy that I talked to is a coworker and I see him about once or twice a week. I am gonna go with the torque sling and see if I notice anything. We are gonna take a look and measure what size piece I need and we'll probably get some type of bushings from local speed shop. The other piece that holds on to the engine can be bought at home depot. The bushings will absorb the pushing of the engine and prevent some of the shaking through the car. As far as the exhaust goes and testing at the dyno I may wait till I have the resources and time to do it.
 

manystangs

Member
Aug 6, 2004
67
0
6
Overland Park, KS
Sep 22, 2006
#6
  • Sep 22, 2006
  • #6
sacrstang said:
Thanks for the answers guys. The guy that I talked to is a coworker and I see him about once or twice a week. I am gonna go with the torque sling and see if I notice anything. We are gonna take a look and measure what size piece I need and we'll probably get some type of bushings from local speed shop. The other piece that holds on to the engine can be bought at home depot. The bushings will absorb the pushing of the engine and prevent some of the shaking through the car. As far as the exhaust goes and testing at the dyno I may wait till I have the resources and time to do it.
Click to expand...
I don't know how to put this so here goes. Don't get some half ass junk from Home Depot. Get the solid Motor Mounts and do the job correctly! JMO.
 
P

pspc271

Founding Member
Dec 25, 2001
339
0
0
Dover, DE
Sep 22, 2006
#7
  • Sep 22, 2006
  • #7
There is always trouble when you go shopping for car parts at Home Depot!
 
You must log in or register to reply here.

Similar threads

C
Exhaust 4 Cats required for smog in California?
  • Codosuarus
  • Sep 28, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
1K
Fox 5.0 Mustang Tech Oct 6, 2025
Scottyding73
S
Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
46
Views
3K
1965 - 1973 Classic Mustangs -General/Talk- Jul 16, 2026
Noobz347
M
Too much for me to repair in my current housing situation
  • My Drama Magnet 04 Gt
  • Apr 1, 2026
  • The Welcome Wagon
Replies
8
Views
310
The Welcome Wagon Apr 14, 2026
Noobz347
P
Progress Thread New To Me 1988 GT - trying to set up vacuum lines for upper intake question
  • pindude80
  • May 6, 2025
  • Fox 5.0 Mustang Tech
  • 9 10 11
Replies
214
Views
14K
Fox 5.0 Mustang Tech Mar 28, 2026
pindude80
P
M
Engine Unexplainable Exhaust Pop and Gurgle
  • Mrnissen122
  • Feb 14, 2026
  • Fox 5.0 Mustang Tech
Replies
12
Views
591
Fox 5.0 Mustang Tech Feb 18, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 2005 - 2014 S-197 Mustang -General/Talk-
  • 2005 - 2009 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?