Question while installing SLP LTs..

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 17, 2005

#1

• Apr 17, 2005

• #1

I am installing these headers RIGHT NOW. While the instructions make it seem fairly simple to do, hooking the EGR Valve back up was a PAIN IN THE ASS. And now that it's hooked up it is hitting against the firewall so now I can't get the headers in the right place to bolt them up. Any suggestions would be greatly appreciated!

 

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 17, 2005

#2

• Apr 17, 2005

• #2

bump? someone out there who installed their own headers wanna help out?

 

K

Kilgore Trout

Fried or Broiled ?

10 Year Member

Mar 30, 2005

4,749

95

134

Apr 17, 2005

#3

• Apr 17, 2005

• #3

This is just the first of many, many, many problems you will have with replacing the entire exhaust. Eventually you may get it all straightened out but you check engine light will always come on and your wallet will be a lot thinnier.

Shoulda just done a catback in my humble opinion...

 

B

BigWind330

New Member

Mar 30, 2003

71

0

0

St. Louis, MO

Apr 17, 2005

#4

• Apr 17, 2005

• #4

Try asking over at modulardepot.com or some other sites

 

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 17, 2005

#5

• Apr 17, 2005

• #5

Kilgore Trout said:

This is just the first of many, many, many problems you will have with replacing the entire exhaust. Eventually you may get it all straightened out but you check engine light will always come on and your wallet will be a lot thinnier.

Shoulda just done a catback in my humble opinion...

Click to expand...

If it didn't have problems it wouldn't be a Ford lol j/p

Only a cat-back.. wheres the fun in that??

 

B

bbueschel

New Member

Dec 26, 2004

26

0

0

Maitland, FL

Apr 17, 2005

#6

• Apr 17, 2005

• #6

Sorry I cant help you, but when you take your first ride in it you will think its worth it. Good for about 3-4 tenths off you quarte mile

 

Gunfighter

Founding Member

Nov 30, 1999

186

0

0

Grapevine, TX

Apr 17, 2005

#7

• Apr 17, 2005

• #7

Is it feasible to do some firewall mods? A mallet/hammer or a cutter might be of use.

 

White Stang

Member

Feb 11, 2004

467

0

16

Ft Lauderdale

Apr 17, 2005

#8

• Apr 17, 2005

• #8

The EGR should not be hitting the firewall its close but everything is close with long tubes.

 

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 17, 2005

#9

• Apr 17, 2005

• #9

we took a break from the driver's side lt for now and moved to the passenger side. The fit is MUCH tighter there and it was easier to put on than the driver's side where there's more room lol go figure. I'm sad because I wanted it done today and we're waiting for a guy we know to help us in the morning. But we are gonna get everything ready so all that will be left is to bolt that header, replace the steering, bolt in any motor mounts, and connect it to the x-pipe.

and yeah.. I definately think it's going to be worth it. I've posted on several forums before I bought the LTs and so many people replied and told me they decided against them because of the install. that's part of the reason i like having them, I dunno about a single stang in my area with them

 

B

BigWind330

New Member

Mar 30, 2003

71

0

0

St. Louis, MO

Apr 17, 2005

#10

• Apr 17, 2005

• #10

Well good luck getting it installed tomorrow, I am really looking forward to hearing about your results. You should definetly gets some clips and dyno numbers too. I have been thinking about getting the headers and x for a long time but nobody has ever said much about them.

 

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 17, 2005

#11

• Apr 17, 2005

• #11

BigWind330 said:

Well good luck getting it installed tomorrow, I am really looking forward to hearing about your results. You should definetly gets some clips and dyno numbers too. I have been thinking about getting the headers and x for a long time but nobody has ever said much about them.

Click to expand...

I'll have sound clips definately! I'm making a video about the whole installation with before and after clips. It will be done tomorrow night as long as we finish the exhaust I won't be able to get dyno numbers for awhile, I live no where close to anything except a dynojet (it's still 2 hours away) and I don't think I wanna go there. I will eventually though

 

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 18, 2005

#12

• Apr 18, 2005

• #12

I'd just like to say I dropped the k-member and the install went VERY EASY!

 

helty

some Ukrainian's enjoying a handjob via my credit

Mar 30, 2005

1,461

1

39

Baltimore, MD

Apr 18, 2005

#13

• Apr 18, 2005

• #13

christiesledd said:

I'd just like to say I dropped the k-member and the install went VERY EASY!

Click to expand...

are you saying the install was a PITA, and then after dropping the k-member it went smoother? i've got the slp lt's on the way, so i may ask you for some pointers. me and three of my buddies will be taking on the task. we're all pretty experienced aircraft mechanics, but none of us have any experience working on a 2 valve 4.6, except for me installing the slp loudmouth cat-back, which was very easy. anyway, are you done with it yet? how does it sound? and what did you do about the egr valve rubbing the firewall?

 

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 18, 2005

#14

• Apr 18, 2005

• #14

well this is what happened... we followed the directions SLP sent and it went great. We removed the H pipe and the manifolds, removed the starter, removed the steering colum and pushed it out of the way, and had the EGR tube hanging. We started to bolt up the driver side header first. My problem with the EGR tube may have been caused by the fact that my intake spacer has raised it up a little. But other people have complained about that damn thing too. We screwed on the EGR tube first because it won't reach if you bolt the header first. Once we screwed it on we couldn't move the header into the right position to bolt it on. We messed with it for a couple of hours and took a break. We decided to move to the passenger side headers. That side is much more tight so at first it was hard to get the header pushed up there. But once we did we started screwing in a few bolts and noticed there was a couple that we had no way of reaching. So today we decided we were just going to drop the K-member. After dropping it putting the headers on was VERY easy! We had to bend one of our tools to reach one of the bolts on the headers, but other than that it went great! The was so much more room to work with. I wouldn't even try to do it any other way, just straight up drop the k-member.. you'll be very thankful you did. I've got the headers installed right now and the k-member back into place. We've been working on putting the dipstick casing back in (we forgot to do it before we but the k-member back up). I have to install my SLP O/R X-pipe and Steeda cat-back and then we'll be done I'm gonig to post a video as soon as we're finished. Feel free to pm/email me any questions you have with your install.

 

helty

some Ukrainian's enjoying a handjob via my credit

Mar 30, 2005

1,461

1

39

Baltimore, MD

Apr 18, 2005

#15

• Apr 18, 2005

• #15

thanks for the info man. i'll definitely be in touch with you down the road. heres a quick question. were you able to re-use the stock gaskets or did you have to get new ones?

 

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 18, 2005

#16

• Apr 18, 2005

• #16

SLP sends you two gaskets to use. we decided to use them because the stock ones would have to be cut in order to use. and since they were already flat and thin we figured we'd use the slp ones that are still thick and are unused. we actually broke one of the gaskets when we were trying to install the driver side header and having problems witht he egr tube before we dropped the k-member. good thing autozone carries one almost exactly like the one slp ships.

 

posm6s

New Member

Sep 24, 2003

144

0

0

Eddyville, KY

Apr 19, 2005

#17

• Apr 19, 2005

• #17

christiesledd said:

I won't be able to get dyno numbers for awhile, I live no where close to anything except a dynojet (it's still 2 hours away) and I don't think I wanna go there. I will eventually though

Click to expand...

3 choices. Evensville, Bowling Green, or Nashville. I have seached and these are the ones I found around here. I would like to go to Bowling Green since its less of a travel problem because I know a easy way to get there. But the only place I found there was Holley Performance and I don't know if they let people come in and use their dyno.

 

csledd

Official Ovary Punching Member

Founding Member

Aug 18, 2001

1,115

1

0

Paducah, KY

Apr 19, 2005

#18

• Apr 19, 2005

• #18

the one in evansville is a dynojet (if we're talking about the same one). I didn't know there was one in BG though, I'll be at beach bend soon so I'm gonna have to check that out.

 

caballo

I'm the bastard love child of a threesome gone awr

Jun 4, 2004

0

0

16

Colorado Springs, CO

Apr 19, 2005

#19

• Apr 19, 2005

• #19

Steeda CatBack?! Hmmm... Well howzit sound?

 

posm6s

New Member

Sep 24, 2003

144

0

0

Eddyville, KY

Apr 19, 2005

#20

• Apr 19, 2005

• #20

christiesledd said:

the one in evansville is a dynojet (if we're talking about the same one). I didn't know there was one in BG though, I'll be at beach bend soon so I'm gonna have to check that out.

Click to expand...

Yep, the only one I know of. Here is the link to their website.

When does Beech Bend open for people like us, I have been wanting to go but I am not sure of there times.