• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech

rear end going out?

  • Thread starter Thread starter johnnyt03gt
  • Start date Start date Feb 13, 2010

johnnyt03gt

5 Year Member
Mar 15, 2008
453
5
29
dallas TX
Feb 13, 2010
#1
  • Feb 13, 2010
  • #1
rear end starting to whine not too bad but worse then 3 months ago is it going out ?
if so what will happen also is there an additive or something i can do just to get more time
out of it the rear was served 50.000 miles ago no issues car now has 93k on it
 

wmburns

SN Certified Technician
Aug 14, 2009
5,892
514
204
Houston Texas
Feb 13, 2010
#2
  • Feb 13, 2010
  • #2
Recommend starting out with a visual inspection. Some rear-end parts are easier to replace than others.

A lot of information can be gleaned from the details of the noise. For example a growl is usually wheel bearings. Does the noise happen when driving or coasting? Turning or going straight? Is the noise high/low pitched? What speed/gear does it happen?

Wheel bearings are fairly easy for the home mechanic to replace.

A whine could be carrier bearings, pinion bearings, or incorrect back lash.

Replacing carrier bearings needs a shop press but 98% of the work can be done in the driveway.

A pinion bearing is more difficult for the home mechanic to replace. It can be done but recommend that you do the homework.

Bottom line, many rear end problems can be diagnosed with a visual inspection. It will not get better on its own and in fact may do additional damage if allowed to continue.

Start by removing the rear cover. Inspect the oil. Look for small bits of metal in the sump.

Take out the half shafts and inpect the roller surface. Replace if scored or pitted.

Look at the wear pattern on the ring and pinion teeth. Take the carrier out and look at the bearing surfaces. Pay attention to ANY pits or blueing of the races. Closely look at the bearing rollers. Edges should be rounded. Replace if wore down to sharp edges.

Good luck.
 
You must log in or register to reply here.

Similar threads

Drivetrain Rear end clunk
  • seanmahoney
  • Oct 13, 2025
  • SN95 4.6L Mustang Tech
Replies
3
Views
386
SN95 4.6L Mustang Tech Oct 13, 2025
nickyb
Z
Progress Thread zeth194 - New Guy on the Block
  • zeth194
  • Mar 19, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
439
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 26, 2026
LILCBRA
Resolved Anyway, to tell where this rear end came from based on this picture?
  • x_man586
  • Jun 7, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
170
Fox 5.0 Mustang Tech Jun 7, 2025
x_man586
J
can you use the heads off a H O 302 to put on a regular 302 engine
  • Jan H
  • Feb 25, 2026
  • Other Auto Tech
Replies
6
Views
272
Other Auto Tech May 17, 2026
nickyb
K
Engine 2000 Mustang GT - Fuel issue post-blown spark plug repair
  • kenster1092
  • Feb 26, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
288
SN95 4.6L Mustang Tech Mar 10, 2026
kenster1092
K
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SN95 4.6L Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?