Removing air silencer??

Lilwhitestang · Aug 2, 2006

What the hell is a removed air silencer and how do you do this? I've always wondered what it was.

Shawneebear93 · Aug 2, 2006

If you look at your airbox, in the front on the bottom there is a little snorkel/scoop type piece hanging down (the air silencer). It's plastic and snaps on/off. If you snap it off the inlet hole (in the airbox) is bigger than the hole on the air silencer. I didn't notice much of a difference when I removed mine. If I had pictures I would share them, but if no one takes them by tonight I'll take some for you.

Mr. Rustypwnz · Aug 2, 2006

Well in your sig it says that you have a cai, but basically what tealtiger told ya

Josh

Red_LX · Aug 2, 2006

Like I've told people a hundred times, the snorkel lookin thing is not the air silencer! The big thing that looks like a muffler in the air inlet is the silencer, if you pull it off it necks down to like 1" on the inside. I don't know about the '91-93 cars, but in the '87-90s you can cut the necked-down part out with a knife, and it makes the car sound a lot cooler anyway.

Lilwhitestang · Aug 2, 2006

Oh...I never knew thats what the air silencer was. I already have a 3" Pipe replacing it. But I was messing around in the car and I found a tube running from the back of the airbox to the header. Its about..hmm..a 1 1/2 to inch flexible tube. It was loose so I just took it off. I didn't need that for anything important did I?

Shinlee · Aug 2, 2006

yup, thats the air silencer, without it you step on the gas and you can tell the difference and why its called a 'silencer'

RustBucket · Aug 2, 2006

The flexible tube that runs from the exhaust over to the airbox is a stovepipe. It heats the incoming air when the engine is cold. There's a door in the airbox that selects the pre-heated air or the outside air depending on the feedback from the ACT.

+1 for RedLX's description of the air silencer. The 91-93 cars do have them and if you're patient, you can actually pry them out of both ends of the silencer body without cutting.

Shawneebear93 · Aug 2, 2006

My bad Red_LX.

jims92mustanglx · Aug 13, 2006

I replaced my silencer with a 3 inch aluminum tube that i had custom bent thru race parts solutions, had it bent to a 60 degree bend. and then bought there silicon conectors and polished it up. looks as nice as any cai on the market and it still uses the original air box.

Shawneebear93 · Aug 13, 2006

jims92mustanglx said:
I replaced my silencer with a 3 inch aluminum tube that i had custom bent thru race parts solutions, had it bent to a 60 degree bend. and then bought there silicon conectors and polished it up. looks as nice as any cai on the market and it still uses the original air box.

Post some pictures, and how much did that cost you.
I've been thinking of having my brother bend me some pipe for an intake when he gets back to Vo-Tech at the end of the month.

jims92mustanglx · Aug 15, 2006

I will need to take some photos but i still in the stone ages with camera. you know that long flimsy stuff they used to call film, well as soon as i get them i will post a engine and parts under hood for ya.

Removing air silencer??

Lilwhitestang

New Member

Shawneebear93

Mr. Rustypwnz

Advanced Member

Red_LX

I’m not much help unless you’re looking for ****!

Lilwhitestang

New Member

Shinlee

New Member

RustBucket

New Member

Shawneebear93

jims92mustanglx

New Member

Shawneebear93

jims92mustanglx

New Member

Similar threads

Removing air silencer??

New Member

Advanced Member

I’m not much help unless you’re looking for ****!

New Member

New Member

New Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency