• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

replace tie rods OR steering rack?

  • Thread starter Thread starter NKau
  • Start date Start date Aug 23, 2005

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Aug 23, 2005
#1
  • Aug 23, 2005
  • #1
The inner tie rods on my '89 have gotten bad. I'm not driving the car anymore until I do something about it. My question is, which is more difficult; replacing the inner/outer tie rods, or just replacing the entire rack?

I'm mostly just curious how easy it is to get the inner tie rods out of the rack without removing it. I'd replace the rack without question normally, but the car only has 66K on it, and I'd rather not mess with pulling the original rack if I don't have to.

I appreciate any input you guys have.
 
8

8950HO

New Member
Mar 31, 2005
658
2
0
Aug 23, 2005
#2
  • Aug 23, 2005
  • #2
Inner tie rods aren`t that hard...easier than replacing the rack which could be a pain trying to remove the high and low pressure hose connections due to seizure.
I replaced an inner tie rod last year.
Raise the front wheels high enough to work under the car.

Remove the flexible bellows and slide them down the tie rod out of the way.

The end of the inner tie rod has either a rivet or roll pin,(safety feature)that has to be removed.If it`s a rivet,use a chisel and hammer and gently raise the rivet head so you can get a pair of vice grips on it to pull it out.

(note...the rivet or roll pin may be in a position that`s not readily reachable...in this case there`s enough play to loosen the inner tie rod end to expose the rivet/roll pin...

IMPORTANT,when loosening inner tie rods you have to use 2 wrenches,one to hold the rack shaft on the exposed gear teeth in place,(drivers side) and another to loosen the inner tie rod`s so you don`t damage the rack.
I used 2 big adjustable wrenches.

Once the inner tie rod/s are removed from the rack shaft,you loosen the lock nut that threads into the outer tie rod and mark the position on the threads of the old inner tie rod and unscrew it from the outer tie rod.

Then mark the approximate position on the threads of the old inner tie rod onto the new inner tie rod and thread it in and tighten the lock nut.

Then attatch the nut of the inner tie rod to the rack shaft and tighten while holding the other end on the gear teeth.Once tightened,install the new supplied rivet/roll pin.I`m pretty sure there`s a few positions for the new rivet/roll pin on replacement inner tie rods compared to the one hole of the stocker,so you can tighten it down without having to worry about the holes not being accessable.

Install the flexable bellows and make an appointment for a wheel alignment,as the toe spec will likely be a little off.

Whew...hope this helps.

But if your rack is leaking,a new rack would be in order.
Mine is still original and has never leaked.I`ve changed the fluid over the years and fairly recently used Valvoline Synpower PS fluid with seal conditioner/stop leak for some extra insurance.

Just be sure to use 2 wrenches when removing/installing inner tie rods.
 

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Aug 24, 2005
#3
  • Aug 24, 2005
  • #3
Hey man, thanks a lot for the detailed reply.
 
You must log in or register to reply here.

Similar threads

J
Suspension Foxbody mustang Steering shaft issue
  • Jakub2537
  • Sep 5, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
331
Fox 5.0 Mustang Tech Sep 11, 2026
gkomo
7
Wheels-Tires Front end shimmy on 79 foxbody
  • 79fox2245
  • Jul 4, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
591
Fox 5.0 Mustang Tech Jul 7, 2025
General karthief
J
Severe shaking/vibrations in steering wheel
  • jacket999
  • May 20, 2025
  • SN95 V6 Mustang Tech
Replies
8
Views
1K
SN95 V6 Mustang Tech Jun 1, 2025
NtheGAME
N
B
Take a look at my rack!
  • bicknell
  • Sep 1, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
9
Views
850
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 13, 2025
Willybill32
H
Strange steering/brake issue
  • Haxmaster
  • Jun 2, 2026
  • SN95 4.6L Mustang Tech
Replies
1
Views
181
SN95 4.6L Mustang Tech Jun 3, 2026
squeak93
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?