Serpentine Belt Problems

jimkochanski

New Member
Aug 13, 2006
2
0
0
The A/C Compressor (with "Factory Air" and not "dealer air") died in my 93 GT about 18 months ago and the Compressor Clutch recently failed catastrophically. Since I cannot afford to replace the Compressor and it seems silly to replace the Compressor Clutch if I am not going to have A/C anyway, I decided to buy a shorter Serpentine Belt and simply bypass the A/C Compressor Clutch Pulley.

Makes sense, right?

An original Ford sticker under the hood contains a diagram with both the belt routing with and without the A/C Compressor superimposed over each other. The only difference in the routing is the presence or absence of the A/C Compressor Pulley. While the specs for a 93 GT w/o A/C call for an 84.5" belt, it was too small, as was an 85.5" belt. FYI… An 86.5" belt was too big. With the Automatic Tensioner down bottom of the belt between the Automatic Tensioner and the P/S Pump laid upon the top of the belt wrapped around the Fan Pulley.

With the Automatic Tensioner up, I was able to get an 86.0" belt on with the help of a screwdriver and a fair amount of effort, but when I released the Automatic Tensioner, the "bottom" of the belt between the P/S Pulley and the Automatic Tensioner Pulley came within 1/16" of the "top" of the belt as it travels around the Fan Pulley. (Once the belt stretches just a little, the "bottom" of the belt and the "top" of the belt will most definitely touch as it did with an 86.5" belt.)

Some ideas I have considered include:

(1) If possible and if advisable, reducing the force that the Automatic Tensioner applies to the belt.

(2) Replace the Automatic Tensioner with a manually adjusted tensioner.

(3) Moving either or both the Alternator and/or P/S Pump up. (The problem is I do not see what would appear to be a Pivot Bolt and a Slide Bolt. Everything looks like it is in a fixed position.)

Any suggestions on what the heck I should do?

Thanks!
 
If you remove the compressor, you are supposed to move the PS pump in it's place. You can by brackets at places like 50resto.

That is how a non-ac car is setup...if I am not mistaken.

Until then, why don't you just pull the compressor clutch assy off, remove the coil, and put just the pully and clutch hub back on? That way you will have a free spinning pulley, just as it is supposed to be with the AC off, but with the coil removed you shouldn't have any issues with it locking up or causing drag on the belt.
 
to bypass the a/c you HAVE to move the ps pump up or by an idler pulley.

http://www.buyfordracing.com/shop/product_info.php?products_id=354

Its cheap and easy, this is the one I bought, shouldnt take more then 30 mins to install with normal tools. This eliminates the a/c compressor and moves the ps pump up, while your down there if you have a catless mid pipe get rid of the smog pump. I run a 74.5" short belt and noticed a very nice gain in performance from the shorter belt and lost weight. smog and a/c weigh about 40 pounds. If your not willing to do all that just leave the compressor on and run a stock belt and forget about it, the a/c is a free pulley when not turned on anyways.

heres with the a/c

0000717gl2.webp



after a/c gone

engine13yn.webp
 

Attachments

  • 0000717gl2.webp
    0000717gl2.webp
    2.8 KB · Views: 169
  • engine13yn.webp
    engine13yn.webp
    2.8 KB · Views: 205
Another Idea:
You don't need to move the P/S pump, I think that looks awful anyways. Go to March Perfomance and they have kits to do what you want to do. I used the ALT kit, (I have my smog pump gone) comes with the tensioner, and the P/S kit that keeps the P/S pump in the same location, but removes all the brackets for the A/C. Looks good and keeps things in their place. You will need to remove the P/S pulley and put it back on.