• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

setting tps

  • Thread starter Thread starter blkstangman88
  • Start date Start date Dec 25, 2004

blkstangman88

New Member
Apr 6, 2004
646
0
0
Dec 25, 2004
#1
  • Dec 25, 2004
  • #1
today i went to check and adjust my tps and the volts read .93. i adjusted it to .99 with the key in the on position. my question is what happins to the engine with the tps set lower then it should? less gas or what?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Dec 25, 2004
#2
  • Dec 25, 2004
  • #2
as long as it is within parameters, the computer zeroes the baseline reading out.
 

giddyup306

Founding Member
Oct 22, 2002
3,041
2
59
Dec 25, 2004
#3
  • Dec 25, 2004
  • #3
Anything over .954V is "rich" but hissin is right.
 

90mustangGT

I felt sorry for girls because
Founding Member
Jan 15, 2002
2,773
17
89
Dallas, GA
Dec 25, 2004
#4
  • Dec 25, 2004
  • #4
Below 1V the computer reads as closed throttle, while 1V and up it is reading this as part throttle. So if it is set too low, you push the gas partly open but the computer thinks it's still closed, as well as when you punch it the computer has less time to react. If you are really set low, your computer won't read WOT when it is becuasee it won't make it that far. I noticed that idle quality and throttle responce is definatly effected.
 

blkstangman88

New Member
Apr 6, 2004
646
0
0
Dec 25, 2004
#5
  • Dec 25, 2004
  • #5
when i set the tps back to .99 volts, i didnt have to push the gas as much to get the same response. well its good now and thanx.
 

Michael Yount

Mustang Master
Apr 10, 2002
9,039
6
79
Charlotte, NC
Dec 25, 2004
#6
  • Dec 25, 2004
  • #6
Lots of myth and urban legend out there around this one. Since 88 the ecu resets a baseline for tps throttle closed voltage each time the car is started. It doesn't matter where it's set as long as it's somewhere between about .7V and 1.3V. Anywhere in there is fine. There is absolutely no benefit to resetting it to "as close to 1V as you can get it" - where ever you set it with in the range described above is only good until the next time the throttle is closed - and it baselines all over again.
 
You must log in or register to reply here.

Similar threads

Engine Vacc leak detector
  • Creomod
  • Jul 19, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
198
Fox 5.0 Mustang Tech Jul 25, 2026
Mustang5L5
B
Help! Fox with idle issues
  • bbarton
  • Sep 11, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
277
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 12, 2026
AeroCoupe
7
What megasquirt kit to order
  • 74delta
  • Jul 4, 2026
  • Digital Self-tuning Forum
Replies
15
Views
617
Digital Self-tuning Forum Aug 26, 2026
fasterthangas
F
R
TPS
  • Redguy69
  • May 5, 2025
  • 1994 - 1995 Specific Tech
Replies
1
Views
153
1994 - 1995 Specific Tech May 5, 2025
Noobz347
S
Engine Stalls when downshifting/coasting
  • Scott_S
  • Nov 5, 2025
  • Fox 5.0 Mustang Tech
Replies
11
Views
878
Fox 5.0 Mustang Tech Nov 6, 2025
Mustang5L5
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?