Shifter Vibration******

super302 · Dec 9, 2004

I was out driving in my slow5.0, and got on it to see how fast i could get up to 60mph, (new street, no houses/businesses, cars etc.) I got up to about 4700rpms or so in first gear and the shifter vibrated a lot, so i slowly put it into 2nd, same thing happened when i got up that high in 2nd gear too, and 3rd gear. After that i said screw it and went home!

What the hell is happening

Also, what rpms should i be shifting at with my puny mods

Thanks,
Patrick

super302 · Dec 9, 2004

Also, i could hear the tranny whining pretty bad (had radio off, windows up, soooo....)

Any diagnosises (sp?)

Labora · Dec 9, 2004

3rd gear will probably whine a bit. As for the rattling @ higher RPM's check your balancer. Mine does it a bit but not to bad I guess..

GRGT1994 · Dec 9, 2004

Did you recently change your shifter (or haven't run with the windows up much since putting it in)? That might be the source.

Otherwise, maybe the shift lever bolts have worked loose a bit.

These suggestions probably don't apply if you could feel the vibration coming through the seat (rather than the shifter).

Al J · Dec 9, 2004

Pop the shifter boot & check the bolts that fasten the stick to the tower. They've worked loose & need tightening w/a dab of Locktite.
Also, I've have both & I notice that Pro-5.0 is noisier than Steeda.

chaos254 · Dec 9, 2004

super302: i have the same problem as you! At around ~4800 rpms my shifter is vibrating like crazy. Happens in all the gears, I'm out at school so I haven't been able to look into the problem but I go home next week. I'm definately going to check the shifter bolts and if its not them(hopefully it is!) I will drop the tranny and see what I can find. I'll let you know if I figure it out and vice versa.

GTJake · Dec 9, 2004

Balancer. Check it.

Jake

Green95 · Dec 9, 2004

Same thing happened with my 84 GT. I changed the balancer, flywheel. Turned out to be the pilot bearing. If there is any play, the input shaft will wobble around and cause everything to vibrate especially at higher rpm's. Took me a while to figure it out. It is annoying cuz I didn't want to get on it very hard. So, if you try the balancer and flywheel and you have time, rip out the tranny and replace the pilot bearing.

mo_dingo · Dec 9, 2004

Has the transmission been removed recently? Had any drivetrain work been performed recently???

If when someone was removing the transmission, they let it hang on the input shaft while not bolted in place, then the input shaft may be bent slightly.

But check the balancer first.
Scott

slo65 · Dec 9, 2004

not to hi-jack, but i'm having the same problem, how would i check to see if the balancers bad? also kinda scared to ask but how much do new ones go for

GTJake · Dec 10, 2004

Check behind the balancer to see if the rubber is coming out at all. If it is, it's time to upgrade.

Jake

super302 · Dec 11, 2004

well, i tightened the bolts that connect the handle to the base stick on the tri-ax, put some lok-tite on there, doesn't seem to vibrate anymore,

thanks everyone,
Patrick

Shifter Vibration******

super302

I'd do anything for free Bapples

super302

I'd do anything for free Bapples

Labora

GRGT1994

New Member

Al J

Member

chaos254

GTJake

Green95

New Member

mo_dingo

slo65

New Member

GTJake

super302

I'd do anything for free Bapples

Similar threads

Shifter Vibration******

I'd do anything for free Bapples

I'd do anything for free Bapples

New Member

Member

New Member

New Member

I'd do anything for free Bapples

Similar threads

Privacy & Transparency

Privacy & Transparency