• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Simple Upgrades?

  • Thread starter Thread starter gregsmy
  • Start date Start date Jan 29, 2008
G

gregsmy

Member
Jan 9, 2008
30
0
6
Jan 29, 2008
#1
  • Jan 29, 2008
  • #1
I am building a 36 Ford street rod truck that has the 5.0 HO engine and trans from a 87 Lincoln Mark VII LSC. It has an aftermarket "Painless" wiring harness for the EFI and has been changed over to MAF. Everything else about the engine and trans are stock. Are there any simple and inexpensive bolt ons that would improve power or fuel economy? I am not looking for any high horsepower gains, just interested to see if there are things I can do that would improve the performance or gas mileage. Things I have looked at include a new chip for the ECM, larger throttle body, and a shift kit for the trans. I figured I would ask here to see if those would be a waste of time at this point or if there are other areas to look into. Thanks
 

bullitstang1313

Member
Jan 21, 2003
713
0
16
Indianapolis / Columbus, Indiana
Jan 29, 2008
#2
  • Jan 29, 2008
  • #2
Are you running stock accessories, i.e. water pump, alternator, powersteering? You could lose the powersteering or if you want to keep it you can free up some horsepower by going with underdrive pulley's. You could switch to an electric fan but make sure your alternator can handle the extra load.
 

stykthyn

I want to measure mine. It doesn't look that tall.
15 Year Member
Jul 6, 2006
5,232
2,652
223
gainesville
Jan 29, 2008
#3
  • Jan 29, 2008
  • #3
a/c delete, underdrive pulleys, electric fan, and a set of headers will be the cheapest things you can do the motor. 3.73 or higher gears in the rear will help with in town mileage and give you good seat of the pants feel down low.
 

ttop88

Member
Mar 12, 2007
42
0
6
indiana
Jan 29, 2008
#4
  • Jan 29, 2008
  • #4
1.7 roller rockers and a K&N filter.
 
G

gregsmy

Member
Jan 9, 2008
30
0
6
Jan 29, 2008
#5
  • Jan 29, 2008
  • #5
I am running headers with a new 2.5" exhaust system and no catalytic converters. So far stock accesories including a/c, pwr strng, and alternator. Will probably be running a electric fan due to limited clearance problems.

Need to figure out how to decode the diff tag to see what gears it has. It also came out of the LSC with the disc brakes.

Anything to be gained by changing the ECM? I see people looking for the ones with the "A" code?

What kinda of gain to be expected by changing to the 1.7 rockers? That seems like any easy to do change if the perfromance is worth the price. Whats an average price for a set of rockers?

Thanks again
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Jan 29, 2008
#6
  • Jan 29, 2008
  • #6
Changing the computer won't get you any real improvments in performance at your current HP level.

On a budget? do the junkyard upgrade...

Check the size ofthe MAF in your car. Stock was 55 MM for most early Mass Air engines.

94-95 Mustang GT MAF - $40-$100. It is 70 MM instead of the stock 55 MM on regular stangs built prior to 94. It uses a slip on duct on the side that goes to the throttle body and a 4 bolt flange on the other. You need a flange adapter to fit the stock slip on air ducting that goes to the air box. Wiring plugs right in with no changes. *1 *2

95-97 Ford Explorer intake manifold & throttle body $150-$300. The intake manifold flows 220 CFM +, much better than stock. Throttle body is 65 MM, bigger than the 60 MM on stock stangs. I got a 96 with EGR passages that match the stock setup, so my smog gear works just like factory. You’ll need a 65 MM EGR spacer & new gaskets for $65-$90 so you have a place to mount the EGR & throttle linkage.

3G alternator from 94-95 Mustangs or other Ford. $20-$120. A must have to make the electrical system work like it should. You’ll need a 4 gauge power wire and a 125-135 amp fuse to go with it about $15- $30.

Lincoln MK VIII electric fan -$40-$160. Free up some HP by not having to drive the stock fan. The 3G alternator upgrade is a must have prerequisite before you do the MK VIII fan. You won’t have enough electrical power if you don’t do the 3G upgrade.

*1.) A metal flange adapter is available from: http://www.kustomz.com/cat3.html . Buy the TR70 for $44.95.

*2.) MAF & sensor interchange
The 94-95 Mustang 5.0 MAF & sensor is also found on:
1995-94 Mustang 3.8L F2VF-12B579-A2A,
1994-92 Crown Victoria 4.6L F2VF-12B579-A2A,
1995-94 Mustang, Mustang Cobra 5.0L F2VF-12B579-A2A,
1994-92 Town Car 4.6L F2VF-12B579-A2A,
1994-92 Grand Marquis 4.6L F2VF-12B579-A2A,
The A2A, AA, AB, etc, on the end of the part number are minor changes that do not affect the calibration.
 
9

92mustanggt509

New Member
Dec 11, 2007
32
0
0
Washington
Jan 29, 2008
#7
  • Jan 29, 2008
  • #7
what about a cold air intake, or new spark plugs and wires, maybe new ignition
 

samickguy15

Member
Sep 1, 2005
404
0
16
Delavan, IL
Jan 29, 2008
#8
  • Jan 29, 2008
  • #8
92mustanggt509 said:
what about a cold air intake, or new spark plugs and wires, maybe new ignition
Click to expand...

If he's putting it in a '36 he's going to have a custom air cleaner anyways... Good plugs, wires, and maybe an MSD would be good.
 

ttop88

Member
Mar 12, 2007
42
0
6
indiana
Jan 29, 2008
#9
  • Jan 29, 2008
  • #9
The rearend most likely has 3.27's. the top row of the tag should say 88327. the 88 means it's a 8.8"ring gear. the last 3 is your gear ratio. What's the car weigh? Best bang for the buck may be 3.73 gears and a transgo shift kit.
 
G

gregsmy

Member
Jan 9, 2008
30
0
6
Jan 30, 2008
#10
  • Jan 30, 2008
  • #10
I will check the gears and see what they are, probably 3.27's.

Is there any benefit to changing the MAF up to the 65 or 70mm without doing any other mods? I was thinking of looking around for a gt-40 / explorer intake but need to figure something out first. Due to the tight space of the 36 front end, I had to flip the upper intake around and use a spacer to clear the brake booster. On the older style intake thats not a problem because you can mount it either way and it will still bolt on, I am not sure about the gt-40 though.
 

ttop88

Member
Mar 12, 2007
42
0
6
indiana
Jan 30, 2008
#11
  • Jan 30, 2008
  • #11
GT-40 style was originally made for the 93 lightning. It was reversed on them.

View attachment 333355
 
G

gregsmy

Member
Jan 9, 2008
30
0
6
Jan 30, 2008
#12
  • Jan 30, 2008
  • #12
So is that true for the explorer intake as well? That setup has a ton of clearance on the drivers side. Even better than the older style. Is the trans and throttle cables easy to change over?

On a different note, I was going over things and checking the previous owners work when I discovered that he has the original MAP sensor plugged into the connector for the MAP sensor but with no vacumn line attached. I have read that they are similiar in function but calibrated differently. Should I replace it? It has a "Painless" wiring harness and the connector is labeled BPS (barometric pressure switch?).
 
You must log in or register to reply here.

Similar threads

Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
720
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
F
Ford 460 swap
  • Ford460
  • Sep 13, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
6
Views
494
1996 - 2004 SN95 Mustang -General/Talk- Sep 14, 2026
Ford460
F
G
Hello and Instrument Wiring
  • GT Jon
  • Jul 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
194
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 6, 2026
Mustang5L5
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
W
Speedometer and shifting issues
  • wyatt-tetro891
  • Aug 17, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
6
Views
317
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 18, 2026
wyatt-tetro891
W
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?