smog delete pipes

P

pony50boy302

New Member

Aug 29, 2007

18

0

0

Feb 16, 2008

#1

• Feb 16, 2008

• #1

the previous owner of my can took out the smog pump and left the pipe thats connected to the 2 heads and just put a cap on it ..

is it ok to leave it like that or is it bad to have that extra pressure lingering in there .. i had these plugs that were laying around i thought was just for those holes .. they are a little over 5/8ths wide and 7/16 long with the allen key head ..can i use them ? and will anything leak from the head or pipe if i remove the pipe ?
any info would be very much appreciated thanks fellas

 

Attachments

• cc86a81b5868.webp

  11 KB · Views: 124

mustangfan1990

New Member

Jul 17, 2005

505

1

0

Lenoir, North Carolina

Feb 16, 2008

#2

• Feb 16, 2008

• #2

all I did was unbolted the pipes from the back of the heads and put bolts in th ehole. I found 2 bolts that threaded right in.

 

P

pony50boy302

New Member

Aug 29, 2007

18

0

0

Feb 16, 2008

#3

• Feb 16, 2008

• #3

did you use the same bolts you took out ?

 

bloopbloob

Member

Sep 27, 2006

578

4

16

Alberta

Feb 16, 2008

#4

• Feb 16, 2008

• #4

you need two 5/8" 11tpi bolts about 1" long to plug the holes in the back of the heads. or you can use a spark plug. or leave the tubing capped. or cut the blocks off the tubing and flip them and rebolt them back on.

 

bloopbloob

Member

Sep 27, 2006

578

4

16

Alberta

Feb 16, 2008

#5

• Feb 16, 2008

• #5

pony50boy302 said:

did you use the same bolts you took out ?

Click to expand...

those bolts only hold the tubing to the heads. they are much smaller than the threaded passageway that you need to plug

 

myslo50

Member

Jun 12, 2006

247

3

18

ohio

Feb 16, 2008

#6

• Feb 16, 2008

• #6

unless u clear out the threads there gona be a pita to thread in. and if the heads are on the car, good luck cleaning the holes. u can take the crossover pipe off, cut the pipe off the little blocks, take the blocks and flip them around and put them back on the heads. if the heads are off, clean the threads and put bolts in them. your local ford dealer should have thermactor hole plugs for sale. i think i paid like $5 for 2, 5 yrs ago. just a thought

 

mustangfan1990

New Member

Jul 17, 2005

505

1

0

Lenoir, North Carolina

Feb 16, 2008

#7

• Feb 16, 2008

• #7

yeah thats the size 5/8s....I didnt have a problem plugging my holes cause my heads was new, but when I had the stock heads I just pinched the pipe

 

bloopbloob

Member

Sep 27, 2006

578

4

16

Alberta

Feb 16, 2008

#8

• Feb 16, 2008

• #8

myslo50 said:

unless u clear out the threads there gona be a pita to thread in. and if the heads are on the car, good luck cleaning the holes. u can take the crossover pipe off, cut the pipe off the little blocks, take the blocks and flip them around and put them back on the heads. if the heads are off, clean the threads and put bolts in them. your local ford dealer should have thermactor hole plugs for sale. i think i paid like $5 for 2, 5 yrs ago. just a thought

Click to expand...

it wasn't too bad for me. i had a lot of carbon in there, but i just worked the bolts back and forth kind of like you would a tap. I went to the local bolt supply store, and just asked for a 5/8" bolt, 11 threads per inch, about 1" long. cost me 15 cents each.