Dan_Soprano
15 Year Member
North East SSoM Members!!!
- Thread starter whitehorseupnorth
- Start date
Dan_Soprano
15 Year Member
I couldn't get the website to load for a long time last night then I couldn't open any of the forums. Must be some big problems again.
Been working on the stang. The driveshaft loop is done. DRilled the hole and mounted the battery cut off switch. Can't finish the switch until I get some more cable. Oh well that will be done next weekend. Found out that my pushrods should be about 1/16" shorter.
What was everyone up to this weekend?
Been working on the stang. The driveshaft loop is done. DRilled the hole and mounted the battery cut off switch. Can't finish the switch until I get some more cable. Oh well that will be done next weekend. Found out that my pushrods should be about 1/16" shorter.
What was everyone up to this weekend?
Dan_Soprano
15 Year Member
went and saw Motley Crue in Pornd last weekend with Mike W. They were ok, but the croud was gay, so it brought the mood down big time.gaslight said:
gaslight said:
I ended up working yesterday. Normally I would not work on a weekend, but the extra cash is always good. Nothing got done on the Cobra yesterday, or today, this weekend was crap!! I am going to order a Dynojet Wideband Commander this week, and hopefully have it by the weekend so I can install it. This will give me the ability to datalog and send the files to James for a dead on tune
Dan_Soprano
15 Year Member
Naa, I knew it was going to be an older crowd, and it was.........The energy just wasn't there. I saw them in 2000 when Vince first came back, and even though Tommy wasn't with them then, it was AWESOME!!! It was a MUCH bigger venue last time though. Like I said, they were good, crowd sucked though.gaslight said:
EDIT: I did see ALOT of boobies!!!!!
Dan_Soprano
15 Year Member
damn money bags!!!!Badstang00 said:I ended up working yesterday. Normally I would not work on a weekend, but the extra cash is always good. Nothing got done on the Cobra yesterday, or today, this weekend was crap!! I am going to order a Dynojet Wideband Commander this week, and hopefully have it by the weekend so I can install it. This will give me the ability to datalog and send the files to James for a dead on tune
Dan_Soprano
15 Year Member
yeah well. It was something different to do. The good thing was we were literally RIGHT ON the stage. I could have spit and hit any of them!!!gaslight said:
DoubleONegative
Active Member
Ok boys here they are
with the 9.5psi pulley by tuned by Jerry at SCT the numbers are as follows
Mustang Dyno SAE
438RWHP and 405RWTQ with a 11.8 a/f
the best part is i hit 400RWTQ at 3800rpm and it stayed above 400 to 5600
I wish it were dyno jet numbers but hey i am pleased the first run netter 442RWHP but it was detonating alittle bit. You couldn't hear it but Jerry's laptop indicated it.
average RWHP was 321 and RWTQ was 380
with the 9.5psi pulley by tuned by Jerry at SCT the numbers are as follows
Mustang Dyno SAE
438RWHP and 405RWTQ with a 11.8 a/f
the best part is i hit 400RWTQ at 3800rpm and it stayed above 400 to 5600
I wish it were dyno jet numbers but hey i am pleased the first run netter 442RWHP but it was detonating alittle bit. You couldn't hear it but Jerry's laptop indicated it.
average RWHP was 321 and RWTQ was 380
DoubleONegative
Active Member
I had to leave at 1pm so i could get back to see the Crue with dan....so i didn't get to see larry run
Dan_Soprano
15 Year Member
DoubleONegative
Active Member
Similar threads
