• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Starter stays engaged and cranking

  • Thread starter Thread starter 1991ragtopgt
  • Start date Start date Nov 1, 2011
1

1991ragtopgt

New Member
Nov 1, 2011
4
0
0
Crawfordsville, IN
Nov 1, 2011
#1
  • Nov 1, 2011
  • #1
The starter on my 1991 gt 5 speed occasionally stays engaged and continues to crank the engine after the car starts. Turning off the ignition and releasing the clutch does nothing. I have to disconnect the battery. I have replaced the starter, battery, and solenoid after the first occurrance. Then it happened again a year later, which was just last week. I guess my next step is possibly the ignition switch. I've heard this has happened to other fox owners. Any suggestions?
 

Stever89

5 Year Member
Dec 14, 2009
536
9
39
Biloxi, MS
Nov 1, 2011
#2
  • Nov 1, 2011
  • #2
Clean (wire brush) all your connections in the starting circuit pos. and ground, at the battery, solenoid, starter. Wire brush all your chassis/engine block ground connections as well. It doesn't hurt, it's free, and it may solve your problem. Good luck!
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Nov 1, 2011
#3
  • Nov 1, 2011
  • #3
You posted a TECH question in Talk. This limits your chances of getting some really good advice, since most guys aren't looking for Tech stuff in the Talk forum.

Having said that, here’s some help…


No Crank checklist for 5.0 Mustangs

Revised 05-Oct-2010 to update Fluke references.

No crank. slow crank and stuck starter solenoid problems have the same root causes – low battery voltage and poor connections. For that reason, they are grouped together.
Use the same initial group of tests to find the root cause of both no crank and stuck solenoid problems.

Since some of the tests will bypass the safety interlocks, make sure that the car is in neutral and the parking brake is set. Becoming a pancake isn’t part of the repair process…


1.) Will the car start if it is jumped? Then clean battery terminals and check battery for low charge and dead cells. A good battery will measure 12-13 volts at full charge with the ignition switch in the Run position but without the engine running.
A voltmeter placed across the battery terminals should show a minimum of 9.5-10 volts when the ignition switch is turned to the Start position and the starter engages or tries to engage. Less than this will result in a clicking solenoid, or slow cranking (if it cranks at all) or a starter solenoid that sticks and welds the contacts together.

Most auto parts stores will check your battery for free. It does not have to be installed in the car to have it checked; you can carry it with you to the auto parts store.

The battery posts and inside of the battery post terminals should be scraped clean with a knife or battery post cleaner tool. This little trick will fix a surprising number of no start problems.

The clamp on with 2 bolts battery terminal ends are a know problem causer. Any place you see green on a copper wire is corrosion. Corrosion gets in the clamped joint and works its way up the wire under the insulation. Corroded connections do not conduct electricity well. Avoid them like the plague...

If the starter solenoid welds the contacts, then the starter will attempt to run anytime there is power in the battery. The cables and solenoid will get very hot, and may even start smoking. The temporary fix for a welded starter solenoid is to disconnect the battery and smack the back of the solenoid housing a sharp blow with a hammer. This may cause the contacts to unstick and work normally for a while.

A voltmeter is handy if you are familiar with how to use it to find bad connections. Measure the voltage drop across a connection while trying to start the car: more than .5 volts across a connection indicates a problem. The voltage drop tests need to be done while cranking the engine. iI's the current flowing through a connection or wire that causes the voltage drop.

See http://assets.fluke.com/appnotes/automotive/beatbook.pdf for help for help troubleshooting voltage drops across connections and components. .



2.) Check the battery to engine block ground down near the oil filter, and the ground behind the engine to the firewall. All grounds should be clean and shiny. Use some sandpaper to clean them up.

3.) Jump the big terminals on the starter solenoid next to the battery with a screwdriver - watch out for the sparks! If the engine cranks, the starter and power wiring is good. The starter relay is also known as a starter solenoid.

The rest of the tech note only concerns no crank problems. If your problem was a stuck solenoid, go back to step 1.

4.) Then pull the small push on connector (small red/blue wire) off the starter solenoid (Looks like it is stuck on a screw). Then jump between the screw and the terminal that is connected to the battery. If it cranks, the relay is good and your problem is in the rest of the circuit.

5.) Remember to check the ignition switch, neutral safety switch on auto trans and the clutch safety switch on manual trans cars. If they are good, then you have wiring problems.

Typical start circuit...
Diagram courtesy of Tmoss & Stang&2birds



6.) Pull the starter and take it to AutoZone or Pep Boys and have them test it. Starter fails test, then replace it. If you got this far, the starter is probably bad.


Starter solenoid wiring for 86-91 Mustang



Starter solenoid wiring 92-93 Mustang or earlier Mustang with upgraded high torque mini starter.


Electrical checks for the switches and starter solenoid

Remove the small red/blue wire from the starter solenoid. Use a screwdriver to bridge the connection from the battery positive connection on the starter solenoid to the small screw where the red/blue wire was connected. The starter should crank the engine. If it does not, the starter solenoid is defective.

If the starter does crank the engine, the problem is in the clutch safety circuit (5 speed) or Neutral Sense Switch (auto trans) or ignition switch.


Typical start circuit...
Diagram courtesy of Tmoss & Stang&2birds


You will need a voltmeter or test lamp for the rest of the checks. Connect one lead of the voltmeter or test lamp to ground. The other lead will connect to the item under test.
Look for 12 volts on the white/pink wire when the ignition switch is turned to the Start position. Check the ignition switch first.
No 12 volts, replace the ignition switch.

The next step will require you to push the clutch pedal to the floor (5 speed) or put the transmission in neutral (auto trans) while the ignition switch is turned to the Start position.
Good 12 volts, check the clutch safety switch (5 speed) or Neutral Sense Switch (auto trans) for good 12 volts on both sides of the switches. No 12 volts on both sides of the switch and the switches are defective or out of adjustment. Check the wiring for bad connections while you are at it.
 
1

1991ragtopgt

New Member
Nov 1, 2011
4
0
0
Crawfordsville, IN
Nov 2, 2011
#4
  • Nov 2, 2011
  • #4
Thank you

Thanks for the information, gentlemen. I appologize for the wrong posting location, I guess I don't know exactly where to post my tech questions. In a blog or forum or thread? Kinda confusing. This elaborate concept is new to me.
 

Kdubslugga

Active Member
Jun 7, 2003
1,515
3
38
Akron, OH
Nov 2, 2011
#5
  • Nov 2, 2011
  • #5
Ohhh I just chased this problem for a yr... Is your battery mounted in the trunk?
 
1

1991ragtopgt

New Member
Nov 1, 2011
4
0
0
Crawfordsville, IN
Nov 2, 2011
#6
  • Nov 2, 2011
  • #6
no, stock location
 

Kdubslugga

Active Member
Jun 7, 2003
1,515
3
38
Akron, OH
Nov 2, 2011
#7
  • Nov 2, 2011
  • #7
1991ragtopgt said:
no, stock location
Click to expand...

Good, cause i had voltage drop issues with my long cables. Is your car an auto or a 5 speed. Reason I ask, is I believe on an Automatic, the Neutral Safety Switch is tied into the starting circuit. If it's an an auto try starting in in Neutral instead of park. If your a 5 speed. All it can be is.

1. Starter
2. Solenoid
3. Solenoid to Starter cable
4. Weak Battery and or corroded cables
5. Bad Ground"s"
6. Igntion Switch
7. Ignition Lock cylinder

Are you familiar with how to use a test light? If so you need one!
 
1

1991ragtopgt

New Member
Nov 1, 2011
4
0
0
Crawfordsville, IN
Nov 3, 2011
#8
  • Nov 3, 2011
  • #8
Kdubslugga said:
Good, cause i had voltage drop issues with my long cables. Is your car an auto or a 5 speed. Reason I ask, is I believe on an Automatic, the Neutral Safety Switch is tied into the starting circuit. If it's an an auto try starting in in Neutral instead of park. If your a 5 speed. All it can be is.

1. Starter
2. Solenoid
3. Solenoid to Starter cable
4. Weak Battery and or corroded cables
5. Bad Ground"s"
6. Igntion Switch
7. Ignition Lock cylinder

Are you familiar with how to use a test light? If so you need one!
Click to expand...

Have one and know how to use it. I have about half of your suggestions complete and will start on the rest soon. I will keep you all updated. Again, thanks for the information.
 
You must log in or register to reply here.

Similar threads

S
All power lost at crank
  • saf_blu302
  • Mar 7, 2026
  • 1994 - 1995 Specific Tech
Replies
4
Views
395
1994 - 1995 Specific Tech Mar 12, 2026
General karthief
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
405
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
M
85 mustang 5.0 cranking in run position
  • Mamaclean
  • May 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
264
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 1, 2026
General karthief
A
1987 5.0 speed density Foxbody crank no start
  • Alan2204
  • May 23, 2026
  • Fox 5.0 Mustang Tech
Replies
10
Views
598
Fox 5.0 Mustang Tech May 30, 2026
Mcmahst
T
Electrical 1990 Vert starting/Solenoid issues
  • Tom77
  • Apr 18, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
524
Fox 5.0 Mustang Tech Apr 18, 2025
85GTStangGuy
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?