still need help with ignition

90lxfoxbody

Member
Jan 11, 2006
264
0
16
ok..... third time asking for help. tried every fusible - all good. rechecked the fusebox and every fuse - all good - nothing out of place. when i turn the key over i get nothing. no gauges register - please someone help me with this. is this what happens when the ignition switch goes out?
 
The ignition switch going bad can cause all sorts of ridiculous problems.. blinkers not working, dead accessories, etc. If you haven't replaced it lately, might as well give it a try.. they're relatively cheap anyway. Did you check the grounds in the engine compartment?
 
yep - checked all the ground wires etc. i am going to pick up another ignition switch tomorrow since they are only ten dollars. only time is not on my side. i posted another thread earlier today documenting the problem. i just can't figure out what would kill the ignition switch like that.
 
Well, the ignition switch is under the steering wheel covers, so chances are if that smoke you are referring to came from under the dash, you fried something else. A wiring diagram and a multimeter and some wire tracing may help more than replacing that switch would. Sounds to me like you burned something up under there.. did you get under the dash and check for other burnt looking wires?
 
yes i crawled around under there with a flashlight and checked everything - even removed the trim and metal plate from the steering column. nothing looks out of place. i don't have a meter and i am supposed to leave for work early in the a.m. - so i am trying to siolate the problem any way i can. thanks for your help by the way - i appreciate it. with the switch in the on position and the battery hooked up i can jump the starter solenoid and the engine will try to turn over. i called black magic's tech line and of course everything they told me aqualed up to "the fan didn't do it" i can;t think of what would make that wire overheat so bad in the first place. leaving the drivebelt should have drained the battery a bit but that's it. the car wasn't moving so the fact that the power steering pump wasn't moving should not have been a factor. so at this point i am entirely bamboozled. i even checked the inertia switch in the back.
 
yes it was replaced in 95 or 96 i think. i checked all the fusibles around the start solenoid and they all look ok - no way to tell for sure without a meter. none of the leads looked burned etc. i am thinking it has to be the ignition switch. would the ignition switch going out cause that to happen?
 
A bad ignition switch could kill power to many of the circuits in the car. Have you taken a look at it yet? A serious meltdown would be visible. Also have you looked at the wires on the backside of the fuse box. You must be missing something because releasing smoke leaves visible evidence a majority of the time.
 
saleen you are correct - i thought the same thing. i crawled under there with a flashlight and took off the steering column cover and checked/rechecked everything. the only melted wire was the slightly melted one from the fusebox to the manual switch i had run. but it was run exactly as the instructions detailed. so i think the toggle switch i had was bad maybe, the wire got hot. it touched one of the wires to the ignition switch and the wire melted through and touched another wire, and the popping noise i heard was the ignition switch going out - and the grey smoke was from the wiring to the toggle switch. that's my guess. i am buying another ignition switch tomorrow and changing it out. i just hope it's not as difficult as the hanes manual makes it look!
 
Sounds like you checked most of you possible culprits. If that's the case it's I'd bet your Pip sensor went out. It's located on the inside wall of your distributor. Shaped like the letter, C. It's very common for them the overheat because of eng temp. If that goes out, you won't get anything... absolutely nothing! Get yourself a new pip senor, cost about $30. R&R takes sometime though because you have to take the distributor apart. So give yourself a good sat afternoon.
 
See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help on 88-95 wiring http://www.veryuseful.com/mustang/tech/engine/

http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

This diagram courtesy of Tmoss & Stang&2birds is your friend...

IgnitionSwitchWiring.gif


Start by looking for 12 volts on the two yellow wires that feed power from the
battery. Test them for 12 volts with the switch on.

MustangFuseBox.gif
 

Attachments

  • IgnitionSwitchWiring.gif
    IgnitionSwitchWiring.gif
    10.1 KB · Views: 131
  • MustangFuseBox.gif
    MustangFuseBox.gif
    23 KB · Views: 140