• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

still need help with ignition

  • Thread starter Thread starter 90lxfoxbody
  • Start date Start date Feb 16, 2006
9

90lxfoxbody

Member
Jan 11, 2006
264
0
16
Feb 16, 2006
#1
  • Feb 16, 2006
  • #1
ok..... third time asking for help. tried every fusible - all good. rechecked the fusebox and every fuse - all good - nothing out of place. when i turn the key over i get nothing. no gauges register - please someone help me with this. is this what happens when the ignition switch goes out?
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Feb 16, 2006
#2
  • Feb 16, 2006
  • #2
The ignition switch going bad can cause all sorts of ridiculous problems.. blinkers not working, dead accessories, etc. If you haven't replaced it lately, might as well give it a try.. they're relatively cheap anyway. Did you check the grounds in the engine compartment?
 
9

90lxfoxbody

Member
Jan 11, 2006
264
0
16
Feb 16, 2006
#3
  • Feb 16, 2006
  • #3
yep - checked all the ground wires etc. i am going to pick up another ignition switch tomorrow since they are only ten dollars. only time is not on my side. i posted another thread earlier today documenting the problem. i just can't figure out what would kill the ignition switch like that.
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Feb 16, 2006
#4
  • Feb 16, 2006
  • #4
Well, the ignition switch is under the steering wheel covers, so chances are if that smoke you are referring to came from under the dash, you fried something else. A wiring diagram and a multimeter and some wire tracing may help more than replacing that switch would. Sounds to me like you burned something up under there.. did you get under the dash and check for other burnt looking wires?
 
9

90lxfoxbody

Member
Jan 11, 2006
264
0
16
Feb 16, 2006
#5
  • Feb 16, 2006
  • #5
yes i crawled around under there with a flashlight and checked everything - even removed the trim and metal plate from the steering column. nothing looks out of place. i don't have a meter and i am supposed to leave for work early in the a.m. - so i am trying to siolate the problem any way i can. thanks for your help by the way - i appreciate it. with the switch in the on position and the battery hooked up i can jump the starter solenoid and the engine will try to turn over. i called black magic's tech line and of course everything they told me aqualed up to "the fan didn't do it" i can;t think of what would make that wire overheat so bad in the first place. leaving the drivebelt should have drained the battery a bit but that's it. the car wasn't moving so the fact that the power steering pump wasn't moving should not have been a factor. so at this point i am entirely bamboozled. i even checked the inertia switch in the back.
 

willys1

Active Member
Dec 2, 2003
1,004
1
36
New Jersey
Feb 16, 2006
#6
  • Feb 16, 2006
  • #6
Fox's had a ignition recall from the factory.Do you know if yours was ever replaced?
 
9

90lxfoxbody

Member
Jan 11, 2006
264
0
16
Feb 16, 2006
#7
  • Feb 16, 2006
  • #7
yes it was replaced in 95 or 96 i think. i checked all the fusibles around the start solenoid and they all look ok - no way to tell for sure without a meter. none of the leads looked burned etc. i am thinking it has to be the ignition switch. would the ignition switch going out cause that to happen?
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Feb 16, 2006
#8
  • Feb 16, 2006
  • #8
A bad ignition switch could kill power to many of the circuits in the car. Have you taken a look at it yet? A serious meltdown would be visible. Also have you looked at the wires on the backside of the fuse box. You must be missing something because releasing smoke leaves visible evidence a majority of the time.
 
9

90lxfoxbody

Member
Jan 11, 2006
264
0
16
Feb 16, 2006
#9
  • Feb 16, 2006
  • #9
saleen you are correct - i thought the same thing. i crawled under there with a flashlight and took off the steering column cover and checked/rechecked everything. the only melted wire was the slightly melted one from the fusebox to the manual switch i had run. but it was run exactly as the instructions detailed. so i think the toggle switch i had was bad maybe, the wire got hot. it touched one of the wires to the ignition switch and the wire melted through and touched another wire, and the popping noise i heard was the ignition switch going out - and the grey smoke was from the wiring to the toggle switch. that's my guess. i am buying another ignition switch tomorrow and changing it out. i just hope it's not as difficult as the hanes manual makes it look!
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Feb 17, 2006
#10
  • Feb 17, 2006
  • #10
This article should help with the switch replacement.

http://www.mustangmonthly.com/howto/5657/
 
W

wazazzle

New Member
Mar 30, 2005
618
1
0
In the dumpster behind McDonalds. WA
Feb 17, 2006
#11
  • Feb 17, 2006
  • #11
Sounds like you checked most of you possible culprits. If that's the case it's I'd bet your Pip sensor went out. It's located on the inside wall of your distributor. Shaped like the letter, C. It's very common for them the overheat because of eng temp. If that goes out, you won't get anything... absolutely nothing! Get yourself a new pip senor, cost about $30. R&R takes sometime though because you have to take the distributor apart. So give yourself a good sat afternoon.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Feb 17, 2006
#12
  • Feb 17, 2006
  • #12
Waz, the PIP wont take out gauges, etc. The motor will still turn over with a bad one, it just wont catch.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 17, 2006
#13
  • Feb 17, 2006
  • #13
See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help on 88-95 wiring http://www.veryuseful.com/mustang/tech/engine/

http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

This diagram courtesy of Tmoss & Stang&2birds is your friend...



Start by looking for 12 volts on the two yellow wires that feed power from the
battery. Test them for 12 volts with the switch on.

 

Attachments

  • IgnitionSwitchWiring.gif
    10.1 KB · Views: 132
  • MustangFuseBox.gif
    23 KB · Views: 141

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Feb 17, 2006
#14
  • Feb 17, 2006
  • #14
Like I said before, the diagram is your friend.

See the following website for some help from Tmoss (diagram designer) & Stang&2Birds (website host) for help on 88-95 wiring http://www.veryuseful.com/mustang/tech/engine

http://www.veryuseful.com/mustang/tech/engine/images/IgnitionSwitchWiring.gif

http://www.veryuseful.com/mustang/tech/engine/images/fuel-alt-links-ign-ac.gif

http://www.veryuseful.com/mustang/tech/engine/images/88-91eecPinout.gif

Diagram courtesy of Tmoss & Stang&2birds
 
You must log in or register to reply here.

Similar threads

D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
207
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
L
2000 Mustang PATS - Broken Key and Wire - HELP!
  • Laree Taylor
  • May 7, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
10
Views
396
1996 - 2004 SN95 Mustang -General/Talk- May 12, 2026
manicmechanic007
Electrical Issues with my 2006 mustang gt
  • VerneVdV
  • May 22, 2026
  • 2005 - 2009 Specific Tech
Replies
0
Views
214
2005 - 2009 Specific Tech May 22, 2026
VerneVdV
W
1993 LX 5.0 dies after ignition parts replacement
  • Warhorse85
  • Aug 16, 2025
  • Fox 5.0 Mustang Tech
  • 5 6 7
Replies
122
Views
5K
Fox 5.0 Mustang Tech Nov 4, 2025
General karthief
S
01 GT DRIVERS SIDE DOOR LOCK CYLINDER LINKAGE
  • Scwhitten
  • May 13, 2026
  • SN95 4.6L Mustang Tech
Replies
3
Views
314
SN95 4.6L Mustang Tech Jun 19, 2026
melo.timo
M
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?