• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

#$%^&^ Stripped Screws

  • Thread starter Thread starter Blakthorn
  • Start date Start date Oct 27, 2005
  • 1
  • 2
Next
1 of 2 Next Last

Blakthorn

Member
Jul 24, 2004
299
1
16
US
Oct 27, 2005
#1
  • Oct 27, 2005
  • #1
I have the worst luck...I stripped the screw trying to get out the top plastic piece of the steering column. The piece above the speedometer with 2 screws 1 on each side. That screw has got to be in the worst place EVER, its right against the windshield and you need maybe a 1 inch screw driver to get that thing out.

I was trying to get behind my headlight switch to see if the wires are still in because only my highbeams and daytimes are working. Highbeams only work if I hold down the switch, not if I flick it on.

Anyway, how the heck do I get stripped screws out, because I also stripped one on the 5.0 Intake plate in the engine bay..
 

Blakthorn

Member
Jul 24, 2004
299
1
16
US
Oct 27, 2005
#2
  • Oct 27, 2005
  • #2
pics of my prob..
 

Luvmy88

New Member
Oct 27, 2003
136
0
0
Oct 27, 2005
#3
  • Oct 27, 2005
  • #3
pull the windshield to do it right...
 

Luvmy88

New Member
Oct 27, 2003
136
0
0
Oct 27, 2005
#4
  • Oct 27, 2005
  • #4
(for the stripped screws)
 

Look Its Aaron

Your car looks like it came straight from Mexico.
Founding Member
Nov 18, 2001
2,634
0
48
Fontana, Cali
Oct 27, 2005
#5
  • Oct 27, 2005
  • #5
Dude you would have used one of those screw drivers that looks like a Z, with a phillips on one end and flathead on the other :/

Sorry to hear about your situation, that REALLY sucks.
 

2000xp8

SN Certified Technician
Aug 8, 2003
8,075
1,658
194
NJ
Oct 27, 2005
#6
  • Oct 27, 2005
  • #6
The screws that are in mine are Torx in the center, but also around the outside i can use a ratchet.

I'm guessing your aren't that way.

So i'd take a New phillips head tip, put it in a 1/4 socket, and then put a ratchet on it, and have someone press down, while you turn it.

Unless someone forceed larger screws in there, they are only held in by those clips.
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Oct 27, 2005
#7
  • Oct 27, 2005
  • #7
You can use an offset screwdriver (the "Z" shaped one,) and use something (a hammer handle with a towel wrapped over it to protect) and then use the hammer to apply downward pressure to the screwdriver while you turn slowly. You can also buy ratcheting types (called dogbones) of screwdrivers that'll work, but they're more expensive.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 27, 2005
#8
  • Oct 27, 2005
  • #8
Very good suggestions on here. I used a really short screwdriver and it worked fine. The pressure idea is key (treating it like an impact driver to keep the tangs on the screwdriver from slipping).

Pushing down on the dash pad can also help - it relieves some pressure against the underside of the screwhead.

Good luck bud.
 

Blakthorn

Member
Jul 24, 2004
299
1
16
US
Oct 27, 2005
#9
  • Oct 27, 2005
  • #9
thanks for all the ideas, i just picked up these 2 things from home depot, tell me if they are helpful..

btw when those screws are out does the whole thing lift off, if you look by your switches (headlight/foglight) there is a seem that goes all the way to the other side, is this made to split or is it still all 1 piece?
 
G

gt90stang

New Member
Dec 7, 2002
568
0
0
Oct 27, 2005
#10
  • Oct 27, 2005
  • #10
Yeah, those may help. I use a small ratcheting handle (from a gun screwdriver kit) that holds hex bits and put downward pressure.

Good Luck, Don
 

sgarlic

Founding Member
Apr 21, 2001
3,085
1
56
Oct 27, 2005
#11
  • Oct 27, 2005
  • #11
It's all one piece. That whole piece from where the screws are to where the hazrad and headlight switches are is the bezel that comes off. Assuming you removed the rest of the screws it'll come out when you remove the last two. (You also of course have to remove the hazard switch and the headlight switch.)
 

Blakthorn

Member
Jul 24, 2004
299
1
16
US
Oct 28, 2005
#12
  • Oct 28, 2005
  • #12
so should i remove those switches before i take that bezel off, cause i think i have to or it wont fit right??

anyway..how do I get them out?
 
G

gt90stang

New Member
Dec 7, 2002
568
0
0
Oct 28, 2005
#13
  • Oct 28, 2005
  • #13
Yes, you have to remove the switches before you remove the bezel. For each switch there are two small locking tabs on each side that must be carefully depressed with a small flat blade screwdriver. Before you disconnect the switchs from the harness make a diagram of the wires and their position for each connector. When these get old the little plastic retainers for the wire socket pins break and the wires will pull out! Figuring out where they go without a diagram took me over 4 hours to figure out.

Don
 
8

89lxsport50

10 Year Member
Feb 25, 2003
550
5
39
Franklin Tennessee
Oct 28, 2005
#14
  • Oct 28, 2005
  • #14
There was a kid on the Corral that busted his windshield out with a hammer to get to those screws. It may take a while but you should be able to get them out using the suggestions above. I am suprized to see philips heads in there, mine are torx. Good luck
 

RsStanG1987

I shaved all my pubes playing this game.
10 Year Member
Mar 13, 2004
569
9
79
Dupont PA
Oct 28, 2005
#15
  • Oct 28, 2005
  • #15
There is also a little metal z brace on the bottom that holds it down.
 

Blakthorn

Member
Jul 24, 2004
299
1
16
US
Oct 28, 2005
#16
  • Oct 28, 2005
  • #16
thanks ill try once i get some free time
 

Blakthorn

Member
Jul 24, 2004
299
1
16
US
Oct 30, 2005
#17
  • Oct 30, 2005
  • #17
AHA! I got the screw out with the Z screwdriver and alot of downforce on it

Anyway I took apart some things and I think I found my problem. I snapped out the headlight switch and foglight switch and I pulled out the grey snap in harness where the wires go into...I follow the yellow/red wire and noticed that the grey front part that snaps into the black switch is burned, it was brown and shaped like it melted. whats this part called and how do i get this fixed! I need headlights!!!
 

cjuroff

Founding Member
Aug 15, 2001
75
0
0
Indiana
Oct 30, 2005
#18
  • Oct 30, 2005
  • #18
This is gonna sound stupid but for future use something that works really well is put a little anti sieze on the tip of the driver. The grit in the anti sieze helps keep the driver from slipping. I know ist sounds crazy but believe me it REALLY works.
 

Blakthorn

Member
Jul 24, 2004
299
1
16
US
Oct 31, 2005
#19
  • Oct 31, 2005
  • #19
I have pics of this! I will get them up tomorrow asap
 

Saleen0679

10 Year Member
Apr 14, 2005
876
24
49
Yakima, WA
Oct 31, 2005
#20
  • Oct 31, 2005
  • #20
If you're talking about the grey six position headlight switch connector like http://dallasmustang.com/prod/W208 it can be found at most places that carry Mustang parts like LRS and Dallas Mustang. You should also be able to find one at a junkyard, just make sure it isn't brittle.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

D
2006 GT Windshield Cowl install
  • Daddidio
  • Mar 12, 2026
  • 2005 - 2009 Specific Tech
Replies
0
Views
290
2005 - 2009 Specific Tech Mar 12, 2026
Daddidio
D
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
204
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
P
Electrical 1988 GT Wrong Cluster- causing electrical issues?
  • pindude80
  • May 6, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
445
Fox 5.0 Mustang Tech May 6, 2025
pindude80
P
S
  • Locked
Drivetrain Adjustable clutch cable questions
  • Scott_S
  • Oct 31, 2025
  • Fox 5.0 Mustang Tech
Replies
6
Views
551
Fox 5.0 Mustang Tech Oct 31, 2025
Noobz347
T
Convertible A-pillar weatherstrip issues
  • thiefofcheese
  • Oct 24, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
468
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Nov 20, 2025
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?