• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

stud mouted guys c'mon in!!!

  • Thread starter Thread starter 97vertstang
  • Start date Start date Jan 3, 2008

97vertstang

Member
Aug 17, 2005
85
0
6
fontana ca
Jan 3, 2008
#1
  • Jan 3, 2008
  • #1
well i just wanted to know size pushrods did you guys end up using???? also are the stock pushrods hardened????
 

jtfairlane

New Member
Mar 5, 2006
468
3
0
Jan 3, 2008
#2
  • Jan 3, 2008
  • #2
Pushrod length will be different for every guy, even for two guys using the same heads.

There is no universal pushrod length for stud mount cylinder heads.

The stock pushrods on late model, pedestal mount small block fords are NOT hardened for use with guideplates.
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Jan 3, 2008
#3
  • Jan 3, 2008
  • #3
One can estimate the new pushrod length by factoring in the difference in lobe lift, between one camshaft and another.

If all else is equal, you can take the difference in lobe lift between camshafts, then multiply by 2. This means that you will need atleast that much more length on the pushrod. It would be a great starting point.

Stock is 6.272" measured as the guage length. If it is done by the measured length it is 6.250".

All the same pushrod

When you go to order custom pushrods (if needed), make sure you know which measurement they use.

- Guage
- Measured

One may use the same pushrod as another, or they could be a few thousandths off.

I see often, the Trickflow (Summit) heads use longer pushrods by nearly half an inch.

The AFR heads use around the 6.2-6.3" range from what I have seen.

You can buy adjustable pushrods for $20.

Good Luck.
 

97vertstang

Member
Aug 17, 2005
85
0
6
fontana ca
Jan 3, 2008
#4
  • Jan 3, 2008
  • #4
thats pretty much the answer that i was looking for. i wanted to get a starting point , since i want to get the car running as soon as i can when i do the HCI on my car.
 
You must log in or register to reply here.

Similar threads

J
Exhaust manifold to Y-pipe nut & stud dimensions?
  • joeybuddy96
  • Jul 7, 2026
  • SN95 V6 Mustang Tech
Replies
2
Views
221
SN95 V6 Mustang Tech Jul 9, 2026
joeybuddy96
J
K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
508
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
Engine Pushrod Length?
  • foxbodyclark
  • Jan 25, 2025
  • Fox 5.0 Mustang Tech
Replies
1
Views
411
Fox 5.0 Mustang Tech Jan 25, 2025
limp
Engine Are These rings OK?
  • PonyGTrider
  • Sep 21, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
343
Fox 5.0 Mustang Tech Sep 26, 2026
PonyGTrider
M
Electrical 93 5.0 No Injector Pulse
  • machinermac
  • Jul 26, 2026
  • Fox 5.0 Mustang Tech
Replies
15
Views
518
Fox 5.0 Mustang Tech Aug 1, 2026
Willybill32
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?