• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

swaping intake tomorrow, question

  • Thread starter Thread starter legalize420
  • Start date Start date Jul 8, 2005
Prev
  • 1
  • 2
First Prev 2 of 2

legalize420

Active Member
May 21, 2005
1,541
1
37
South Florida
Jul 8, 2005
#21
  • Jul 8, 2005
  • #21
i think i am going to use the blue seals that came with the felpro kit. should i put silicone on both sides or just the bottom. any reason why i should not use them and go with just the silicone bead?
 
B

bimmertech

New Member
May 3, 2005
1,123
0
0
merriam, ks
Jul 8, 2005
#22
  • Jul 8, 2005
  • #22
imo the gaskets that are used to seal the front and the back of the lower are completely useless and should be discarded after purchase of said gaskets.
 

cavscout371

New Member
Mar 30, 2005
277
0
0
Jul 9, 2005
#23
  • Jul 9, 2005
  • #23
 

jmoore16

New Member
Jun 1, 2004
91
0
0
Riverview, MI
Jul 9, 2005
#24
  • Jul 9, 2005
  • #24
Don't use the China Wall Gaskets

Don't bother with the blue china wall gaskets that came with the Felpro kit. Use your Ultra Black. It will work great but the gaskets will only work if you are lucky and they don't squeeze out.

Trust us...

Build up a 6 mm wall of Ultra Black, let it set up for a few minutes and then use the guide studs in the head to make sure that the intake drops down squarely on the heads. If you don't have studs, make some by cutting the heads off really long bolts that thread into the intake bolt holes on the head.

John
 

legalize420

Active Member
May 21, 2005
1,541
1
37
South Florida
Jul 9, 2005
#25
  • Jul 9, 2005
  • #25
i finished up putting the new lower on along with the injectors and dizzy. everything is going good so far, just taking a lil break. the only problem is that i broke a vacuum line. its the tiny one that kinda runs along the firewall. what is it. its probally only a couple of mm in size. way smaller than any of the other vacuum lines.
 

legalize420

Active Member
May 21, 2005
1,541
1
37
South Florida
Jul 9, 2005
#26
  • Jul 9, 2005
  • #26
what is the piece on the driver side near the master cylinder with the vacuum hoses going into it. There is B/B , S/C, A/C, and S. i broke the tiny one that goes to the A/C. my ac is low on refrigerant and has some leak detection stuff in it for when i bring it back in to my mechanic. i am bringing it in on monday but can i drive without that A/C vacuum line. the part where it broke is on the passanger side and it goes back into the firewall so its not like i can get it out of there and just replace it. any suggestions
 

jmoore16

New Member
Jun 1, 2004
91
0
0
Riverview, MI
Jul 9, 2005
#27
  • Jul 9, 2005
  • #27
Vacuum tree

It is called a vacuum tree and it does nothing more than distribute vacuum from the source (manifold line) to the other items that need vacuum (brakes, A/C, EVR, etc). You can make your own by purchasing T fittings and plumbing hoses where you want them.

Good job so far.
 

legalize420

Active Member
May 21, 2005
1,541
1
37
South Florida
Jul 9, 2005
#28
  • Jul 9, 2005
  • #28
done. i just have to wait till the morning before i can start it up. now i just have to pray that there are no leaks.
 

jmoore16

New Member
Jun 1, 2004
91
0
0
Riverview, MI
Jul 9, 2005
#29
  • Jul 9, 2005
  • #29
Retorque the intake

Retorque the intake after you start it and get it hot a couple of times. Next weekend's project?

I will keep my fingers crossed...
 

legalize420

Active Member
May 21, 2005
1,541
1
37
South Florida
Jul 10, 2005
#30
  • Jul 10, 2005
  • #30
jmoore16 said:
Retorque the intake after you start it and get it hot a couple of times. Next weekend's project?

I will keep my fingers crossed...
Click to expand...

started car up this morning. everything seems to be right. i did not get a chance to drive around yet because of the rain. i went down my block but not on a main road and not relly over 20 mph. hopefull all goes well when i open it up. just curious, how much money do you think i wiould have had to pay if i had some else do it. as far as next weekend i dont think i will be doing anything. i would say the next project i might try would be removing smog. all that extra stuff is a PITA to work around so it will be nice to get it out. plus i have no cats so its pointless to have it right? anyways, i just wanted to thank everyone again who helped me with this.
 
Prev
  • 1
  • 2
First Prev 2 of 2
You must log in or register to reply here.

Similar threads

Resolved 1999 cobra removed lower intake manifold to crossovertube
  • hvcobra99
  • Sep 6, 2026
  • SVT Tech Forum
Replies
0
Views
166
SVT Tech Forum Sep 6, 2026
hvcobra99
B
97 GT with 03 explorer Eddie Bauer edition 4.6l
  • basbill73
  • May 10, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
146
1996 - 2004 SN95 Mustang -General/Talk- May 11, 2026
squeak93
Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
346
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
J
Intake
  • James S
  • Jul 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
305
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 12, 2026
James S
J
A
Blow through intercooled questions
  • AngryH58
  • Aug 31, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
286
1996 - 2004 SN95 Mustang -General/Talk- Sep 1, 2026
AngryH58
A
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?