swapped cable, now another problem

Night Shifter · Apr 28, 2008

swapped cable, now another problemNOW BIGGER PROBLEM

ok, so i finally got a chance to swap my adj. steeda cable back to my stock cable.. now, the stock cable wont reach the quadrant with the firewall adjuster in. if i take the adjuster off it reaches it just fine... I put the adj. in, adjusted it all the way out, ran the cable through and the cable wont reach the fork on the quadrant by about a friggin milimeter. How do i get the cable to stretch far enough so i can put it on the quadrant?

COramprat · Apr 28, 2008

Did you attach it to the clutch fork first? If so try attaching it to the quadrant then to the clutch fork. You may have to push the fork out a bit. I used a BF screwdriver to move it enough to attach.

98COBRA281 · Apr 28, 2008

i had the same problem, i accually had to cut the outer casing of the cable, i pulled the black plastic thing, that goes in to the fire wall adjuster off, and cut about 1/2in out of it

Night Shifter · Apr 28, 2008

yup, attached it to the fork first... borrowed a jack and it's gone so right now i can't get to the clutch fork... i may be breaking out the dremel and doing some cutting.. thanks for that idea 98

COramprat · Apr 28, 2008

Night Shifter said:
yup, attached it to the fork first... borrowed a jack and it's gone so right now i can't get to the clutch fork... i may be breaking out the dremel and doing some cutting.. thanks for that idea 98

Why cut due to a lack of a jack? Jack stands are cheap and you can use the jack in the trunk.

Night Shifter · Apr 28, 2008

the first time i tried swapping cables, i used the jack in the trunk and some jack stands.. but i live on a hill and my driveway is a gravel hill and my yard is a grass hill and the jack wants to tilt and i just don't trust bein under my car on a hill using that jack even with jackstands.. seems sketchy to me... but, if it comes down to it, i'll use it since the stands held up with the floor jack

rabidscoobie · Apr 28, 2008

98COBRA281 said:
i had the same problem, i accually had to cut the outer casing of the cable, i pulled the black plastic thing, that goes in to the fire wall adjuster off, and cut about 1/2in out of it

On the instuctions for the steeda kit,cable/quadrant/adj it says to do just that too the original cable,so I assume if you use the stock cable that you suppose to do just that...If I sound like a smart a$$ sorry,Im just saying what it says to do.

Night Shifter · Apr 29, 2008

well i got the cable on the quadrant with the adjuster in.. Now the adjuster doesn't work...WTF???????? if i put the adjuster in and run the cable through the firewall, the clutch won't release until the pedal is ALL te way out..and i mean ALL the way out. No matter how far in or out i adjust the adjuster the release point is the same.. if i take the adjuster out and just run the cable through the firewall, it's back to being at a normal position, but then i can't adjust anything and since the poeple that did my clutch last threw away that plastic peice that attaches to the firewall with the stock cable, all i have it a cable running through a big hole...
How can i get my adjuster to work?????? i'm about to drive this car off a friggin cliff

rabidscoobie · Apr 29, 2008

Isnt a healthy clutch suppose to come out on top.Correct me if Im wrong but I thought that the adj just took out slack and freeplay from the pedal,not adjust where the clutch comes out at.My gt after clutch replacement did just that.Steeda tech said that releasing on top was correct.

Night Shifter · Apr 29, 2008

my clutch is releasing where the pedal would be if you had your car off and your foot off the clutch.. my knee comes to my chest almost its releasing so far out... why would my adjuster stop working now?

AdRock · Apr 29, 2008

Did you cut off the piece on the stock cable and also remove the rubber portion?

COramprat · Apr 29, 2008

What kind of quadrant do you have?

Night Shifter · Apr 29, 2008

AdRock said:
Did you cut off the piece on the stock cable and also remove the rubber portion?

Yes i did.. i can take a pic of it if that will make this easier..

I have the steeda double hook quadrant

COramprat · Apr 29, 2008

See if it works better on the other hook.

Night Shifter · Apr 29, 2008

man i tried for like an hour to get it on the 2nd hook.... that's just not gonna happen... why would switching back to the stock cable cause the adjuster to quit working though?

swapped cable, now another problem

Night Shifter

Well-Known Member

COramprat

...I can take it. I think.

98COBRA281

Night Shifter

Well-Known Member

COramprat

...I can take it. I think.

Night Shifter

Well-Known Member

rabidscoobie

Night Shifter

Well-Known Member

rabidscoobie

Night Shifter

Well-Known Member

AdRock

Member

COramprat

...I can take it. I think.

Night Shifter

Well-Known Member

COramprat

...I can take it. I think.

Night Shifter

Well-Known Member

Similar threads

swapped cable, now another problem

Well-Known Member

...I can take it. I think.

Well-Known Member

...I can take it. I think.

Well-Known Member

Well-Known Member

Well-Known Member

Member

...I can take it. I think.

Well-Known Member

...I can take it. I think.

Well-Known Member

Similar threads

Privacy & Transparency

Privacy & Transparency