• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Testing a Starter Solenoid

  • Thread starter Thread starter FordRacing302
  • Start date Start date Oct 22, 2005

FordRacing302

5 Year Member
Oct 1, 2005
384
42
59
Cleveland, TN
Oct 22, 2005
#1
  • Oct 22, 2005
  • #1
Well Im not that good at wiring and when I was wiring up my coil, I wired it dierctly to the solenoid, and I think I blew the solenoid because before I touched the wires the motor turned over fine but now It wont....So is there a test I can do to find out if my solenoid is bad??
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
Oct 22, 2005
#2
  • Oct 22, 2005
  • #2
if the 83's starter solonoid is similar to the 87-93's, you could take a screwdriver and connect both studs on the solonoid. Make sure you have the car in neutral and the parking brake set and/or the wheels chocked because the car should crank and it might jump; might be a good idea to unplug the coil wire so that it definately won't start.

If it doesn't try to crank at all after trying it a couple times to make sure you're making good contact, it might not be the solonoid; this is only if it's like the later fox body cars as I'm not sure if it is or not.

Hope this helps
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Oct 22, 2005
#3
  • Oct 22, 2005
  • #3
James is right. Applied to later model solenoids, if you can remove the slide-on terminal and jump it to the battery lug on the solenoid, and the car starts (observe ALL the safety precautions he outlined above), the solenoid is fine.
If that test fails but it starts by jumping the lugs like James outlined, then the solenoid is likely bad.

Good luck.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Oct 22, 2005
#4
  • Oct 22, 2005
  • #4
Or you can use a multimeter and test for continuity between the two posts with the key off and when you try to start.
 

Black1987Stang

Active Member
Aug 22, 2004
1,422
0
37
Jersey Shore
Oct 22, 2005
#5
  • Oct 22, 2005
  • #5
Or run a short wire from the battery positive post to where the push on connector goes onto.
 
You must log in or register to reply here.

Similar threads

3
Electrical Starter solenoid green wire?
  • 387lx
  • Jun 1, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
249
Fox 5.0 Mustang Tech Jun 2, 2026
AeroCoupe
3
Electrical Starter solenoid out of space?
  • 387lx
  • Jan 22, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
517
Fox 5.0 Mustang Tech Jan 23, 2026
387lx
3
D
Mustang not starting
  • Dawry Ramos
  • Sep 12, 2026
  • 2015 - 2023 Specific Tech
Replies
10
Views
404
2015 - 2023 Specific Tech Oct 3, 2026
Dawry Ramos
D
R
Engine Evap and charcoal cannister leak
  • ryan1994stang
  • Mar 14, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
650
Fox 5.0 Mustang Tech Mar 18, 2026
Mcmahst
Electrical ’86 Mustang – Power Windows/Locks Dead After Terminator X Swap
  • 5.0 Mike
  • Aug 21, 2025
  • Fox 5.0 Mustang Tech
Replies
0
Views
308
Fox 5.0 Mustang Tech Aug 21, 2025
5.0 Mike
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?