• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

timing issue

  • Thread starter Thread starter NOSNotch
  • Start date Start date May 6, 2007

NOSNotch

Founding Member
Oct 20, 2001
577
0
0
South Jersey
May 6, 2007
#1
  • May 6, 2007
  • #1
just swapped my car to efi and got the tremec in today and i'm havin an issue with the timing. i turned the motor to # 1 tdc and dropped the dist in with the rotor pointing right at 1 on the cap. in order to get it to start i had to turn the distributor all the way towards the tstat housing. i tried moving it back to a normal spot and it dies out and wont start back up. hooked the timing light to it and with the distrib as far as it'll go towards the tstat i can only get it up to around 7 degrees. i tried pullin the distributor back out and dropping it one tooth advance and one tooth retard from where it was originally and it wont start.

i bought the distributor used so i dont know if it may be a problem internally or what but i dont wanna just start throwing parts at it. thanks in advance for any help guys
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
May 6, 2007
#2
  • May 6, 2007
  • #2
After you restab the dizzy (to where you dont think you're 'one tooth off' anymore), try turning the dizzy to one side or the other to see if it will start.

Good luck.
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
May 6, 2007
#3
  • May 6, 2007
  • #3
sounds like your 180 degrees out. You probably were not on TDC of the compression stroke. Try restabbing but get the compression stroke this time. Or just restabb the dizzy 180 degrees out from where it is now.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
May 7, 2007
#4
  • May 7, 2007
  • #4
Putting the distributor back in is fairly simple. Pull #1 sparkplug, put your finger in the sparkplug hole, crank the engine until you feel compression. Then line up the TDC mark on the balancer with the pointer on the engine block.

The distributor starts out with the #1 plug wire lined up at about 12:00 with you facing it. Align the rotor to about 11:00, since it will turn clockwise as it slides into place.

Align the distributor rotor up with the #1 position marked on the cap, slide the distributor down into the block, (you may have to wiggle the rotor slightly to get the gear to engage) and then note where the rotor is pointing. If it still lines up with #1 position on the cap, install the clamp and bolt. If not, pull it out and turn 1 tooth forwards or backwards and try again. Put the #1 spark plug back in and tighten it down, put the clamp on the distributor, but don't tighten it too much, as you will have to move the distributor to set the timing. Note that if it doesn't align perfectly with #1 position, you can turn the distributor until it does. The only problem is that if you are too far one way or the other, you can't turn the distributor enough to get the 10-14 degree optimum timing range.

At this point hook up all the wires, get out the timing light and start the engine. Set the timing where your car runs best. Don't forget to disconnect the SPOUT jumper connector when you set the timing, and plug it back in when you finish.

The HO firing order is 1-3-7-2-6-5-4-8.
Non HO firing order is 1-5-4-2-6-3-7-8
 
You must log in or register to reply here.

Similar threads

Strange timing issue
  • 92 Bimini Blue
  • Sep 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
22
Views
739
Fox 5.0 Mustang Tech Oct 20, 2026
rednotch
Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
349
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
F
Fox 1990 Mustang GT 5.0 A9L – Engine suddenly shuts off but immediately restarts when key turned
  • FishermansFriend
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
695
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
General karthief
B
Front window issues
  • bruno
  • Nov 7, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
213
Fox 5.0 Mustang Tech Tuesday at 10:26 PM
AeroCoupe
C
Electrical Fuel Gauge...Help! What did I do or Didn't Do?
  • ChickenDeluxe
  • Sep 3, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
252
Fox 5.0 Mustang Tech Sep 3, 2026
ChickenDeluxe
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?