• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Timing Question!

  • Thread starter Thread starter armadillon
  • Start date Start date Oct 3, 2007
A

armadillon

New Member
Jul 19, 2007
10
0
0
Oct 3, 2007
#1
  • Oct 3, 2007
  • #1
Hey, If you have a stock 1989 302 (MAF, stock E7 Heads, stock cam) and replace the 1.6 pedestal rockers with 1.7 roller rockers, how does it effect your timing?

Cuz that's what I did on my car! I'm having a weird surging/idle problem, and I read the "Surging Idle Checklist", but I need to know how the rockers are affecting my car's timing before I do some of that stuff.

Question 1: What is the normal ideal timing for my car?

Question 2: What should it be at now?
 

bullitstang1313

Member
Jan 21, 2003
713
0
16
Indianapolis / Columbus, Indiana
Oct 3, 2007
#2
  • Oct 3, 2007
  • #2
Changing the rocker arms wouldn't change the timing of the engine. Changing the rocker arms from 1.6 to 1.7 changes the overall lift of the valve-springs. Stock timing is 10 degrees BTDC. Most people advance the timing anywhere from 12-16 degrees BTDC.
 
F

Fox8950

Member
Jun 29, 2007
247
2
18
Oct 3, 2007
#3
  • Oct 3, 2007
  • #3
I have about the same setup as you and installed 1.7s w/ no problems, I'd look elsewhere for the cause. If you have a cold air intake try clocking (rotating) the MAF sensor, they get funny readings off the curve in that pipe sometimes I know it affected how mine idled alot.
 

jtfairlane

New Member
Mar 5, 2006
468
3
0
Oct 3, 2007
#4
  • Oct 3, 2007
  • #4
Installing a set of rocker arms doesn't affect engine timing at all.

If the only variable between your motor running smoothly and now surging/rough idle was the rocker arm install, than more than likely you improperly installed the rockers and that is what's causing your motor to run rough.

Tell us how you installed your rockers, and we can tell you if you screwed it up or not. You have no idea how many people think installing rocker arms "to spec" just means removing all the rocker arms and tightening the new ones down. Did you do that, or did you make sure each piston was at TDC with both valves closed before you torqued down the rockers?
 
A

armadillon

New Member
Jul 19, 2007
10
0
0
Oct 3, 2007
#5
  • Oct 3, 2007
  • #5
THanks for y'alls info so far, it's been a little helpful..i think =)

The way I installed the rockers:

I replaced them one at a time, making sure each one was at TDC and checking valve lash. I had to use shims between a lot of the rockers, it was kinda strange, because on some intake rockers I would use a thick AND thin shim, but on others i would use only a thick.

I know this is kinda fuzzy and really ahrd to describe without y'all have actually being been there (WTF, do I know english?) but I'm trying =)

I think the shims were .003 and .006 and I was torquing them to spec and at the same time listening for when the valves popped open.

The entire time that the group of 4 people I was with were installing them, I was skeptical on the install, so that's probably a good sign.

In the mean time, it seems to be running pretty well.

If it's running ok with only a bit of a weird idle, are there any impending doom(s) I should be aware of?
 
A

armadillon

New Member
Jul 19, 2007
10
0
0
Oct 3, 2007
#6
  • Oct 3, 2007
  • #6
Running well means that the idle will be at 900-950 for about 10 seconds and then jump to about 1000 or 1050 for 10 seconds. Maybe I just can't identify a NORMAL idle since every car I've ever had has had an abnormal one.
 
You must log in or register to reply here.

Similar threads

T
Oil burning on my recently buil 302
  • The blk67
  • May 15, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
250
Fox 5.0 Mustang Tech May 15, 2026
Noobz347
Surging/stalling! problem or tune?
  • djj62478
  • Oct 4, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
405
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 14, 2026
KRUISR
Strange timing issue
  • 92 Bimini Blue
  • Sep 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
22
Views
731
Fox 5.0 Mustang Tech Oct 20, 2026
rednotch
C
Engine Idle cuts out
  • claypoolxx
  • Mar 7, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
25
Views
1K
Fox 5.0 Mustang Tech Jul 24, 2026
alutwon
Engine Surging idle on start-up
  • keel
  • Aug 11, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Oct 31, 2025
keel
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?